ABB ACH580-01 Series 빠른 설치 및 시작 매뉴얼 - 페이지 14

{카테고리_이름} ABB ACH580-01 Series에 대한 빠른 설치 및 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. ABB ACH580-01 Series 17 페이지. Base drive replacement
ABB ACH580-01 Series에 대해서도 마찬가지입니다: 매뉴얼 (16 페이지), 빠른 설치 및 시작 매뉴얼 (17 페이지), 사용 설명서 (8 페이지), 사용 설명서 (7 페이지), 빠른 설치 및 시작 매뉴얼 (17 페이지)

페이지 인쇄
ABB ACH580-01 Series 빠른 설치 및 시작 매뉴얼
1) Typical motor power with no overload capacity (nominal use). The kilowatt ratings apply to most IEC 4-pole motors. The
horsepower ratings apply to most NEMA 4-pole motors.
2) The recommended branch protection fuses must be used to maintain the IEC/EN/UL 61800-5-1 listing.
3) The drive is suitable for use on a circuit capable of delivering not more than 100000 symmetrical amperes (rms) at 480 V
maximum when protected by the fuses given in this table.
4) Refer to
Alternate Fuses, MMPs and Circuit Breakers for ABB Drives (3AXD50000645015 [English])
and circuit breakers that can be used as branch circuit protection.
Terminal data for the power cables
Frame
T1/U, T2/V, T3/W, L1, L2, L3, R-, R+/UDC+
size
Min. wire size
(solid/stranded)
2
mm
AWG
R1
0.2/0.2
24
R2
0.5/0.5
20
R3
0.5/0.5
20
R4
0.5/0.5
20
R4 v2
1.5/1.5
20
R5
6
R6
25
R7
95
3/0
R8
2×50
2×1/0
R9
2×95
2×3/0
1) In 400/480/575 V drives, cable lug or cable clamp is used for grounding.
Notes:
•
The minimum specified wire size does not necessarily have sufficient current carrying capacity at maximum load.
•
The terminals do not accept a conductor that is one size larger than the maximum specified wire size.
•
The maximum number of conductors per terminal is 1.
•
For UL compliance the R2 frame drive will not accept a size larger conductor.
Weights and free space requirements
This table shows the requirements for the ambient conditions when the drive is in operation (installed for stationary use).
Frame
Weights
size
IP21 (UL
IP55 (UL
Type 1)
Type 12)
kg
lb
kg
R1
4.6
10.1
4.8
R2
6.6
14.6
6.8
R3
11.8
26.0
13.0
R4
19.0
41.9
20.0 44.1
R4 v2
20.0
44.1
21.0
R5
28.3 62.4
29.0 64.0
R6
42.4 93.5 43.0 94.8
R7
54
119.1 56.0 123.5 155
R8
69
152.2
77
R9
97
213.9 103
1) Without free space on the sides.
2) Measured from the drive frame, not from the cable box.
Max. wire size
(solid/stranded)
2
mm
AWG
6/4
10
16/16
6
35/35
2
50
1
70
1
6
70
1/0
4
150
300 MCM
240
500 MCM
2×150
2×300 MCM
2×240
2×500 MCM
Free space requirements for vertical installation
IP21 (UL Type 1)
Above
Below
lb
mm
in
mm
10.6
65
2.56
86
3.39
15.0
65
2.56
86
3.39
28.7
65
2.56
53
2.09
53
2.09
200
7.87
46.3
53
2.09
200
7.87
75
2.95
200
7.87
155
6.10
300
11.8
6.10
300
11.8
169.8 155
6.10
300
11.8
227.1 200
7.87
300
11.8
Tightening torque
(solid/stranded)
N·m
lbf·ft
mm
1.0
0.7
16/16
1.5
1.1
16/16
3.5
2.6
35/35
4.0
3.0
35/35
5.5
4.0
35/35
15
11.1
35/35
30
22.1
180
40
29.5
180
40
29.5
2×180
70
51.6
2×180
Stand alone
IP55 (UL Type 12)
2)
2)
Above
Below
in
mm
in
mm
in
137
5.39
116
4.57
137
5.39
116
4.57
200
7.87
53
2.09
53
2.09
200
7.87
53
2.09
200
7.87
100
3.94
200
7.87
155
6.10
300
11.8
155
6.10
300
11.8
155
6.10
300
11.8
200
7.87
300
11.8
for additional UL fuses
PE
Max. wire size
Tightening torque
2
AWG
N·m
6
1.5
6
1.5
2
1.5
2
2.9
2
2.9
-
2.2
1)
1)
1)
350 MCM
9.8
1)
1)
1)
350 MCM
9.8
1)
1)
1)
2×350 MCM
9.8
1)
1)
1)
2×350 MCM
9.8
Side by side
All types
All types
Sides
Above
mm
in
mm
in
150
5.91
200
7.87
150
5.91
200
7.87
150
5.91
200
7.87
150
5.91
200
7.87
150
5.91
200
7.87
150
5.91
200
7.87
150
5.91
200
7.87
150
5.91
200
7.87
150
5.91
200
7.87
150
5.91
200
7.87
14
lbf·ft
1.1
1.1
1.1
2.1
2.1
1.6
1)
7.2
1)
7.2
1)
7.2
1)
7.2
1)
2)
Below
mm
in
200
7.87
200
7.87
200
7.87
200
7.87
200
7.87
200
7.87
300
11.8
300
11.8
300
11.8
300
11.8