Dialogic DM/V1200A-4E1-PCI 빠른 설치 카드
{카테고리_이름} Dialogic DM/V1200A-4E1-PCI에 대한 빠른 설치 카드을 온라인으로 검색하거나 PDF를 다운로드하세요. Dialogic DM/V1200A-4E1-PCI 2 페이지. Dm3 media boards
페이지 인쇄Dialogic
®
DM3 Media Boards
Quick Install Card for PCI
DM/V960A-4T1-PCI
DM/V1200A-4E1-PCI
Part Number
64-0025-02
Copyright © 2001-2007
Dialogic Corporation.
All Rights Reserved.
Before You Begin
Protecting the Board from Damage
CAUTION:
All computer boards are sensitive to
electrostatic discharge ("ESD"). Handle all static-sensitive
boards and components at a static-safe work area,
and observe anti-static precautions at all times.
If you are not familiar with ESD safety precautions, visit
http://www.dialogic.com/support/hwinstall
to learn more.
Unpacking the Board
®
Unpack the Dialogic
DM3 Media Board ("board")
according to the following steps:
1.
Prepare a static-safeguarded work area.
2.
Carefully remove the board from the shipping
carton and anti-static packaging. Handle the
board by the edges and avoid touching the
board's components.
3.
Lay the board on the static-dissipative work
surface.
NOTE: Place boards in static-shielding bags when
carrying boards from station to station.
CAUTION: Do not remove the board from the anti-static
packaging until you are ready to install it. Observe proper
anti-static precautions at all times.
Physical Description
CH4 CH3 CH2 CH1
Red
Yellow
Green
Loopback
7
6
5
4
3
2
1
Configuring the Hardware
Board Identification
®
The DM3 device driver, part of the Dialogic
System
Software, assigns board instance numbers in ascending
order (beginning with 0) as it detects each board in your
system. A board instance number is the identification (ID)
number used by the system software to recognize the
board.
NOTE: If you add a board to the system, the existing
board instance (ID) numbers may change, depending upon
the PCI bus and slot number where the new board is
installed.
Windows System
After the Dialogic hardware and the Dialogic System
®
Software are installed, refer to the Dialogic
Configuration
Manager (DCM) utility to retrieve the board instance (ID)
number(s) assigned to the board(s) in your system.
1.
RJ-48C jacks: Connectors (4) to external digital
telephone network interface.
8
2.
General Network Interface Alarm LED
3.
Power LED
4.
Reset LED
5.
SW1: Rotary switch to set board identification
(Linux systems only).
6.
POST LEDs: Indicate Power On Self Test
(POST) status during power up.
Alarm LEDs: Indicate network alarms for each
trunk.
9
Red: Alarm to indicate loss of signal.
10
Yellow: Alarm to indicate loss of frame
synchronization at far end of external
network.
Green: Indicates signal present; powered up
and receiving signal from external sources.
Loopback: Indicates loopback mode is
activated.
7.
CT/MVIP Bus Termination Jumpers: Bus
signal is terminated when the corresponding
jumper clip is installed. Signal must be terminated
JP2A
JP2B
only on boards at each end of the CT Bus cable.
JP2A: CT Bus termination jumper
JP2B: MVIP Bus termination jumper
8.
P3: CT Bus connector
9.
ISA Edge Retainer
10. Signal Processing Daughterboard
See the DCM online help for more details about board
identification.
Linux System
In a Linux system, you must set SW1 to a unique number
for each DM3 board in your system so that the Power On
Self Test (POST) for the board(s) can complete
successfully. Use a non-magnetic screwdriver to turn SW1
to 1 of 16 board settings, 0-9 or A-F.
®
®
After the Dialogic hardware and Dialogic System
Software are installed, refer to the proper configuration
files to retrieve the board instance (ID) number(s) assigned
to the board(s) in your system. See the Dialogic Software
Installation Guide for Linux for more information about
Linux configuration files.
Installing the Hardware
NOTE: Dialogic recommends that you install Dialogic
®
hardware before Dialogic
software. However, if you are
adding hardware to an existing system, you do not need to
uninstall existing Dialogic software.
1. With your computer on the static-safe work area,
switch off the power and disconnect all power cords
from the electrical outlets.
2. Remove the chassis cover plate.
3. Select an empty PCI expansion bus slot and remove
the slot's retaining screw and access cover plate (if
applicable).
Installing a PCI Board
Remove
Cover
Plate
Computer
Chassis
4. If you are not installing your board in an ISA form
factor PCI slot, remove the ISA edge retainer from
the board.
5. Using the slot's board guides, insert the board edge
connector into the bus slot. Press firmly until the
board is securely seated in the slot.
6. Replace and tighten the slot's retaining screw to
secure the board firmly in the chassis (if applicable).
7. Connect the RJ-48C jacks on the board bracket to the
switch using a digital telephone cross-over cable.
®
®
PCI
Board
32-Bit
PCI Slot
16-Bit
ISA Slot