Dialogic DM/V1200A-4E1-PCI Cartão de instalação rápida

Procurar online ou descarregar pdf Cartão de instalação rápida para Placa PCI Dialogic DM/V1200A-4E1-PCI. Dialogic DM/V1200A-4E1-PCI 2 páginas. Dm3 media boards

Imprimir página

Dialogic

DM3 Media Boards

Quick Install Card for PCI

DM/V960A-4T1-PCI

DM/V1200A-4E1-PCI

Part Number

64-0025-02

Dialogic Corporation.

Before You Begin

Protecting the Board from Damage

CAUTION:

All computer boards are sensitive to

electrostatic discharge ("ESD"). Handle all static-sensitive

boards and components at a static-safe work area,

and observe anti-static precautions at all times.

If you are not familiar with ESD safety precautions, visit

http://www.dialogic.com/support/hwinstall

to learn more.

Unpacking the Board

Unpack the Dialogic

DM3 Media Board ("board")

according to the following steps:

Prepare a static-safeguarded work area.

Carefully remove the board from the shipping

carton and anti-static packaging. Handle the

board by the edges and avoid touching the

board's components.

Lay the board on the static-dissipative work

surface.

NOTE: Place boards in static-shielding bags when

carrying boards from station to station.

CAUTION: Do not remove the board from the anti-static

packaging until you are ready to install it. Observe proper

anti-static precautions at all times.

Physical Description

CH4 CH3 CH2 CH1

Red

Yellow

Green

Loopback

Configuring the Hardware

Board Identification

The DM3 device driver, part of the Dialogic

System

Software, assigns board instance numbers in ascending

order (beginning with 0) as it detects each board in your

system. A board instance number is the identification (ID)

number used by the system software to recognize the

board.

NOTE: If you add a board to the system, the existing

board instance (ID) numbers may change, depending upon

the PCI bus and slot number where the new board is

installed.

Windows System

After the Dialogic hardware and the Dialogic System

Software are installed, refer to the Dialogic

Configuration

Manager (DCM) utility to retrieve the board instance (ID)

number(s) assigned to the board(s) in your system.

RJ-48C jacks: Connectors (4) to external digital

telephone network interface.

General Network Interface Alarm LED

Power LED

Reset LED

SW1: Rotary switch to set board identification

(Linux systems only).

POST LEDs: Indicate Power On Self Test

(POST) status during power up.

Alarm LEDs: Indicate network alarms for each

trunk.

Red: Alarm to indicate loss of signal.

Yellow: Alarm to indicate loss of frame

synchronization at far end of external

network.

Green: Indicates signal present; powered up

and receiving signal from external sources.

Loopback: Indicates loopback mode is

activated.

CT/MVIP Bus Termination Jumpers: Bus

signal is terminated when the corresponding

jumper clip is installed. Signal must be terminated

JP2A

JP2B

only on boards at each end of the CT Bus cable.

JP2A: CT Bus termination jumper

JP2B: MVIP Bus termination jumper

P3: CT Bus connector

ISA Edge Retainer

10. Signal Processing Daughterboard

See the DCM online help for more details about board

identification.

Linux System

In a Linux system, you must set SW1 to a unique number

for each DM3 board in your system so that the Power On

Self Test (POST) for the board(s) can complete

successfully. Use a non-magnetic screwdriver to turn SW1

to 1 of 16 board settings, 0-9 or A-F.

After the Dialogic hardware and Dialogic System

Software are installed, refer to the proper configuration

files to retrieve the board instance (ID) number(s) assigned

to the board(s) in your system. See the Dialogic Software

Installation Guide for Linux for more information about

Linux configuration files.

Installing the Hardware

NOTE: Dialogic recommends that you install Dialogic

hardware before Dialogic

software. However, if you are

adding hardware to an existing system, you do not need to

uninstall existing Dialogic software.

1. With your computer on the static-safe work area,

switch off the power and disconnect all power cords

from the electrical outlets.

2. Remove the chassis cover plate.

3. Select an empty PCI expansion bus slot and remove

the slot's retaining screw and access cover plate (if

applicable).

Installing a PCI Board

Remove

Cover

Plate

Computer

Chassis

4. If you are not installing your board in an ISA form

factor PCI slot, remove the ISA edge retainer from

the board.

5. Using the slot's board guides, insert the board edge

connector into the bus slot. Press firmly until the

board is securely seated in the slot.

6. Replace and tighten the slot's retaining screw to

secure the board firmly in the chassis (if applicable).

7. Connect the RJ-48C jacks on the board bracket to the

switch using a digital telephone cross-over cable.

PCI

Board

32-Bit

PCI Slot

16-Bit

ISA Slot