Miller MIGmatic M-25 소유자 매뉴얼

{카테고리_이름} Miller MIGmatic M-25에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Miller MIGmatic M-25 12 페이지. Air-cooled guns for gmaw and fcaw welding
Miller MIGmatic M-25에 대해서도 마찬가지입니다: 소유자 매뉴얼 (20 페이지), 소유자 매뉴얼 (8 페이지)

페이지 인쇄

OWNER'S MANUAL

M-15, M-25, M-40, And M-40AL Guns (Euro-Connector)

Specifications

ST-801 727

Safety Precautions For GMAW Guns

A. Symbol Usage

Means Warning! Watch Out! There are possible hazards with this

procedure! The possible hazards are shown in the adjoining symbols.

B. GMAW Gun Hazards

WARNING

The symbols shown below are used throughout this manual to call attention to and identify possible

hazards. When you see the symbol, watch out, and follow the related instructions to avoid the hazard. The

safety information given below is only a summary of the more complete safety information found in wire

feeder and welding power source manuals. Read and follow all Safety Standards.

ELECTRIC SHOCK can kill.

1. Always wear dry insulating gloves.

2. Insulate yourself from work and ground.

3. Do not touch live electrode or electrical parts.

4. Repair or replace worn, damaged, or cracked gun

or cable insulation.

5. Turn off welding power source before changing

contact tip or gun parts.

6. Keep all covers and handle securely in place.

HOT SURFACES can burn skin.

1. Allow gun to cool before touching.

2. Do not touch hot metal.

3. Protect others from contact with hot metal.

FLYING PIECES OF METAL or DIRT can

injure eyes.

1. Wear safety glasses with side shields or face

shield.

Air-Cooled Guns For GMAW And FCAW Welding

M-15 Rated At 150 Amperes Using CO

Flux Cored Wires.

M-25 Rated At 200 Amperes Using CO

Cored Wires (Also Feeds .023 in (0.6 mm) Wire – See Parts List)

M-40 Rated At 400 Amperes Using CO

Flux Cored Wires.

M-40AL Rated At 275 Amperes Using Mixed Shielding Gas; Feeds .047 in (1.2 mm) Aluminium Wire

This group of symbols means Warning! Watch Out! Possible ELECTRIC SHOCK and HOT PARTS hazards.

Consult symbols and related instructions below for necessary actions to avoid the hazards.

October 1996

Use above FORM number when ordering extra manuals.

Shielding Gas. Feeds .023 To .035 in (0.6 To 0.9 mm) Hard Or

Shielding Gas. Feeds .030 To .045 (0.8 To 1.1 mm) Hard Or Flux

Shielding Gas. Feeds .035 To 5/64 in (0.9 To 2.0 mm) Hard Or

Y Marks a special safety message.

Means NOTE; not safety related.

WELDING WIRE can cause puncture

wounds.

1. Keep hands and body away from gun tip when

trigger is pressed.

OVERUSE can damage gun and void

warranty.

1. Follow rated duty cycle.

2. Allow cooling period.

3. Reduce current or reduce duty cycle before

starting to weld again.

1. Read and follow these instructions and all safety

blocks carefully.

2. Have only trained and qualified persons install,

operate, or service this unit.

3. Call your distributor if you do not understand the

directions.

4. For WELDING SAFETY and EMF information,

read wire feeder and welding power source

manuals.

FORM: OM-180 516A



1996 MILLER Electric Mfg. Co.