Miller Digital Performance Series 소유자 매뉴얼 - 페이지 14
{카테고리_이름} Miller Digital Performance Series에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Miller Digital Performance Series 32 페이지. Auto-darkening helmets
Miller Digital Performance Series에 대해서도 마찬가지입니다: 매뉴얼 (32 페이지), 매뉴얼 (28 페이지)
페이지 인쇄
1-1. Sensitivity Control
4-6.
Sensitivity Control
A Digital Elite lens is
shown.
�
1
Sensitivity Adjustment
A Digital Elite lens is shown.
Buttons
1 Sensitivity Adjustment Buttons
2
Mode Control Button
2 Mode Control Button
Use control to make the lens
more responsive to different
Use control to make the lens more respon-
light levels in various welding
sive to different light levels in various welding
processes. Use a Mid-Range
processes. Use a Mid-Range or 30-50%
or 30 50% sensitivity set-
sensitivity setting for most applications.
ting for most applications.
It may be necessary to adjust helmet sensi-
It may be necessary to adjust
tivity to accommodate different lighting condi-
helmet sensitivity to accom-
tions or if lens is flashing On and Off.
modate
different
conditions or if lens is flashing
The sensitivity ranges for each mode are as
On and Off.
follows:
The sensitivity ranges for
Weld, Cut, X-Modes - 0–10
each mode are as follows:
Weld, Cut, X-Modes
Grind Mode - No sensitivity adjustment
Grind Mode
Do not weld in the Grind mode; the
adjustment
lens will not darken.
!
Do not weld in the Grind
�
mode; the lens will not
X-Mode is not present on Performance
darken.
helmets.
Sensitivity Adjustment Procedure
Stick Electrode
Short Circuiting (MIG)
Pulsed And Spray (MIG)
Gas Tungsten Arc (TIG)
Plasma Arc Cutting/Welding
OM-256476 Page 12
Sensitivity Adjustment
Procedure
lighting
0–10
No sensitivity
Recommended Sensitivity Settings
X-Mode is not present on
Performance helmets.
�
Adjust helmet sensitivity in lighting con-
ditions helmet will be used in.
� Press Auto On/Off button to turn helmet
Adjust helmet sensitivity
On.
in lighting conditions hel-
� Press Mode button to select desired
met will be used in.
function: Weld, Cut, or X-Mode.
� Use Sensitivity Less and More buttons
Press Auto On/Off button
to adjust sensitivity control to lowest
to turn helmet On.
setting.
Press Mode button to se-
� Face the helmet in the direction of use,
lect
desired
function:
exposing it to the surrounding light
Weld, Cut, or X-Mode.
conditions.
Use Sensitivity Less and
� Press sensitivity More button until the
More buttons to adjust
lens darkens, then press Less button un-
sensitivity control to low-
til lens clears. An alternative method is
est setting.
to press and hold the Less button until
the lens clears.
Helmet is ready for use. Slight readjustment
may be necessary for certain applications or
if lens is flashing on and off.
�
Reduce Sensitivity setting if lens stays
dark longer than Delay setting.
Mid-Range
Low/Mid-Range
Mid-Range
Mid/High-Range
Low/Mid-Range
2
1
Face the helmet in the di-
rection of use, exposing it
to the surrounding light
conditions.
Press sensitivity More
button until the lens dark-
ens, then press Less
button until lens clears. An
alternative method is to
press and hold the Less
button until
the
clears.
Helmet is ready for use.
Slight readjustment may
be necessary for certain
applications or if lens is
flashing on and off.
Reduce Sensitivity set-
ting if lens stays dark
longer than Delay setting.
OM-256476 Page 1
lens