Aquasana AQ-SFRO 소유자 매뉴얼 - 페이지 3

{카테고리_이름} Aquasana AQ-SFRO에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Aquasana AQ-SFRO 13 페이지. Under sink water filter smartflow reverse osmosis

페이지 인쇄

INSTALLATION STEPS

1 Setup

For systems that include a dedicated faucet:

NOTE: This system requires an existing faucet hole 1" to 1-1/2" in diameter in the

sink or countertop to install the supplied dedicated faucet. You may also replace

an existing kitchen sink sprayer, soap dispenser, or pre-existing hole on the sink or

countertop.

If using a hole from a current dedicated faucet, ensure the hole is 1" to 1-1/2"

in diameter.

If drilling a new hole, ensure faucet body will mount flat against surface and there is

sufficient tubing between faucet body and system manifold. If drilling, we strongly

recommend using a professional. Please wear safety glasses when drilling.

For systems without a dedicated faucet:

NOTE: An airgap is required by code for RO systems. If you don't purchase an airgap

faucet, you must install an airgap under the sink.

This system requires an existing faucet hole, please refer to the installation guide of

the faucet purchased to determine hole size needed to drill.

This system requires tubing to be ¼" outside diameter. If you have 3/8" outer

diameter tubing, you will need to purchase quick connect adapters.

A. Unpack and unwrap box contents.

B. Turn off COLD water supply. Turn on the kitchen faucet to release

pressure and allow water to drain from the line.

C. Temporarily place system manifold and water tank into the under

sink cabinet or desired location to ensure adequate space and proper

positioning.

D. Measure blue and red tubing from faucet hole to system manifold, then

measure yellow tubing from the top of the water tank to the system

manifold. Ensure all tubing lengths are sufficient for making connections.

Do not cut tubing before following next instructions.

E. Remove system manifold and water tank from under your sink to begin

installation.

15.7"

(39.87 cm)

13.74

(34.9 cm

9.06"

(23 cm)

DRAWING NOT TO SCALE, SYSTEM AND TANK ENLARGED.

Install Air Gap Faucet

NOTE: If you have purchased a separate air gap faucet, please skip step 2 and follow

the manufacturer's installation manual. Once the faucet is installed, proceed to step 3.

NOTE: The max countertop width for the faucet is 0.5". If you have a countertop

width greater than that (0.5"-2"), you will need to remove the white plastic piece

from the faucet prior to installing. If you remove the piece, ensure you reassemble

the parts you removed before continuing.

A. Feed pre-connected air gap faucet through

countertop hole.

B. Underneath countertop, slide the slotted

faucet washer onto threaded base of faucet.

Washer should be in between countertop

and white plastic spacer. If needed, loosen

nut to move spacer down to create

enough room for the washer.

C. Tighten nut with adjustable wrench.

Do not over tighten.

WARNING: Ensure all electrical appliances and outlets are turned off at

circuit breaker before continuing. Please wear safety glasses when drilling.

INSTALLATION STEPS

STAGE 4

__________________________________

Remineralizer

AQ-SFRO-REMIN

Adds back calcium to improve

water taste and pH balance.

12.93"

Replace Remineralizer every

10.25"

6 months for best use.

(33 cm)

(26 cm)

Scan to view Performance Data Sheet,

)

2.125"

4.5"

(5.4 cm)

(11.5 cm)