AquaScape AquaJet 600 교육 및 유지 관리 - 페이지 4
{카테고리_이름} AquaScape AquaJet 600에 대한 교육 및 유지 관리을 온라인으로 검색하거나 PDF를 다운로드하세요. AquaScape AquaJet 600 16 페이지. Pond pump
AquaScape AquaJet 600에 대해서도 마찬가지입니다: 지침 및 유지보수 매뉴얼 (16 페이지), 빠른 시작 매뉴얼 (12 페이지)
페이지 인쇄
• Always operate the pump fully submerged. Failure to do
so will overheat the pump and cause it to fail, thus voiding
the warranty. DO NOT OPERATE DRY!
• Use only in fully assembled state, and be sure that both
the upper and lower cage screens are snapped together.
Failure to operate the pump without the filter cage closed
will allow large debris to enter the pump, causing the
pump to fail and voiding the warranty.
• Do not wear loose clothing that may become entangled in
the impeller or other moving parts.
• Keep clear of suction and discharge openings. DO NOT
insert fingers into pump with power connected.
• Do not pump hazardous materials or liquids, such as oil,
saltwater, or organic solvents.
• Do not block or restrict pump outlet.
• Products returned must be cleaned, sanitized, or
decontaminated, as necessary, prior to shipment to
Model Number
Pond Size Recommendation
Maximum Fountain Height (Daisy Fountain)
Motor Type
Wattage
Amperage
Power Cord Length
Discharge Hose Diameter
Discharge Hose Diameter on Diverter
Installation
• Unpack the diverter valve and thread the collar clockwise
directly onto the pump discharge male thread. Do not
overtighten or use any tools (Ex. 1).
• The diverter valve has two flow-control valves (Ex.2).
– The accessory diverter valve controls water flow to any
additional filters, fountains, or waterfalls.
– Side valve controls water flow to attached fountain head.
4
AquaJet Pond Pump Specs
600
1200 US gallons
up to 47"
Mag-Drive
33
.55
25'
with nozzle fountain heads
½", ¾"
Typical installation in a water feature
☎
US (866) 877-6637 |
ensure that employees will not be exposed to health
hazards in handling said material. All applicable laws and
regulations shall apply.
IMPORTANT: Aquascape, Inc. is not responsible
for losses, injury, or death resulting from a failure
to observe these safety precautions, misuse or
abuse of pumps or equipment.
AquaJet
Pond Pump Specifications
®
• Input Voltage: 120V AC
• Input Frequency: 60 Hz
• Submersible pump
• For outdoor or indoor use
• Thermal protection
• Pump rated for use with water only
• Input current intensity and power in watts: See table below
1300
1300 US gallons
up to 62"
Mag-Drive
110
1.00
25'
with nozzle fountain heads
½", ¾"
Ex. 1
• The side valve controls the fountain height, but the
accessory valve will also have an effect on the fountain's
height. As more accessory flow is desired the amount
of water flowing to the fountain will diminish. Closing the
accessory valve will maximize flow to the fountain head.
• Thread the riser stem base onto discharge. Riser stems
can be added to the base stem as desired to increase the
fountain height to the best level for your water feature and
to compensate for different pond depths.
• Insert additional riser stems and lock into position (Ex. 3).
• Thread riser stem base onto discharge (Ex. 4).
☎
CAN (866) 766-3426 | aquascapeinc.com
2000
2000 US gallons
up to 65"
Mag-Drive
250
2.60
25'
with nozzle fountain heads
½", ¾", 1"
Accessory Diverter
Valve
Side Valve
Ex. 2