Aquatec ocean e-vip 사용 설명서 - 페이지 8

{카테고리_이름} Aquatec ocean e-vip에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Aquatec ocean e-vip 16 페이지.

페이지 인쇄

5.1

Assembling the commode

5.1.1

Mounting the seat frame

CAUTION!

Risk of injury due to pins that slide out

Make sure to lock the safety clips.

Lock all casters using the red foot pedals. To do

this, push down the red foot pedal for the casters.

Remove the drive for the tilt adjustment (10, fig. 1)

for the frame (7, fig. 1). To do this, cut through the

cable tie.

Push the fork (2, fig. 2) on the lower end of the

drive (1, fig. 2) onto the lug (4, fig. 2) on the rear

edge of the frame and align the holes with each

other.

Insert one 35 mm pin (5, fig. 2) from the outside

into the hole and push it all the way in.

Attach a safety clip (3, fig. 2) on the inside.

Push the cable (2, fig. 3) for the drive (4, fig. 3) as

far as possible into the frame (1, fig. 3).

Use the enclosed cable tie (3, fig. 3) to fix the ca-

ble for the drive in this position.

Important!

When folded up, the armrests must face for-

ward.

Insert the seat frame (6, fig. 4) into the holes (8,

fig. 4) in the frame (10, fig. 4).

Insert both 35 mm pins (7, fig. 4) into the holes (8,

fig. 4) from outside, push them all the way in, and

attach the safety clips (9, fig. 4) on the inside.

10. Tilt the seat frame until the holes in the holder (5,

fig. 4) on the seat frame and in the fork (1, fig. 4)

on the drive for the tilt adjustment (4, fig. 4) are in

alignment.

11. Push the 23 mm pin (2, fig. 4) from outside into

the holes and attached the safety clip (3, fig. 4) on

the inside.

5.1.2

Fitting the footrests

Important!

The assembly procedure is the same for the

right and the left footrests.

Push the footrest (1, fig. 5) and the footplate (2, fig. 5)

inwards to the guide (7, fig. 5) on the seat frame (6,

fig. 5) until the groove (5, fig. 5) catches the pin on the

clip (8, fig. 5). The footrests can no longer be turned to

the sides.

5.1.3

Fitting the headrest

Important!

●

To adapt it to the user, the grab handle (3,

fig. 6) can be fitted with the curve facing the

front or the back.

●

The headrest pad (10, fig. 6) can be re-

moved and replaced by other pad shapes

(optional). To remove it, loosen the retain-

ing bolts (9, fig 6).

Use the star handle to insert the screw (6, fig. 6) a

little into the bracket (7, fig. 6).

Push the bracket with the screw onto the handle

of the backrest (5, fig. 6) from behind in such a

way that the screw engages in the hole of the

backrest's handle.

Insert the plate (4, fig. 6) into the bracket from the

front in such a way that both lugs of the plate face

down and up and the curved plate side touches

the handle of the backrest.

Important!

On inserting the retainer, the curved side of the

plate must rest entirely on the handle of the

backrest.

Push the grab handle (3, fig. 6) from above into

the recesses of the bracket.

Use the star handle to tighten the screw (6, fig. 6)

until the grab handle is fixed.

Push the pad (10, fig. 6) and the pad holder (2,

fig. 6) into the holder (8, fig. 6) on the grab handle.

Use the star handle to tighten the upper screw (1,

fig. 6) until the pad holder is fixed.

5.1.4

Attaching the chest belt

Important!

●

Attach both fastening clamps at the same

height.

●

The assembly procedure is the same for

the left and the right fastening clamp.

On the backrest cover, open the belt lock of the

belt at the height where the chest belt is to be at-

tached.

Feed this belt along the backrest frame and close

again.

Place the inside part (4, fig. 7) of the fastening

clamp around the backrest frame.

Push the outer part (2, fig. 7) of the fastening

clamp onto the internal thread (3, fig. 7) of the pin

on the inside part.

Use the star handle (1, fig. 7) to attach the chest

belt (5, fig. 7) to the fastening clamp with a screw.