Aquatec ocean e-vip Operating Instructions Manual - Page 8

Browse online or download pdf Operating Instructions Manual for Mobility Aid Aquatec ocean e-vip. Aquatec ocean e-vip 16 pages.

Print Page
5.1

Assembling the commode

5.1.1

Mounting the seat frame

CAUTION!
Risk of injury due to pins that slide out
Make sure to lock the safety clips.
1.
Lock all casters using the red foot pedals. To do
this, push down the red foot pedal for the casters.
2.
Remove the drive for the tilt adjustment (10, fig. 1)
for the frame (7, fig. 1). To do this, cut through the
cable tie.
3.
Push the fork (2, fig. 2) on the lower end of the
drive (1, fig. 2) onto the lug (4, fig. 2) on the rear
edge of the frame and align the holes with each
other.
4.
Insert one 35 mm pin (5, fig. 2) from the outside
into the hole and push it all the way in.
5.
Attach a safety clip (3, fig. 2) on the inside.
6.
Push the cable (2, fig. 3) for the drive (4, fig. 3) as
far as possible into the frame (1, fig. 3).
7.
Use the enclosed cable tie (3, fig. 3) to fix the ca-
ble for the drive in this position.
Important!
When folded up, the armrests must face for-
ward.
8.
Insert the seat frame (6, fig. 4) into the holes (8,
fig. 4) in the frame (10, fig. 4).
9.
Insert both 35 mm pins (7, fig. 4) into the holes (8,
fig. 4) from outside, push them all the way in, and
attach the safety clips (9, fig. 4) on the inside.
10. Tilt the seat frame until the holes in the holder (5,
fig. 4) on the seat frame and in the fork (1, fig. 4)
on the drive for the tilt adjustment (4, fig. 4) are in
alignment.
11. Push the 23 mm pin (2, fig. 4) from outside into
the holes and attached the safety clip (3, fig. 4) on
the inside.
5.1.2

Fitting the footrests

Important!
The assembly procedure is the same for the
right and the left footrests.
Push the footrest (1, fig. 5) and the footplate (2, fig. 5)
inwards to the guide (7, fig. 5) on the seat frame (6,
fig. 5) until the groove (5, fig. 5) catches the pin on the
clip (8, fig. 5). The footrests can no longer be turned to
the sides.
EN
5.1.3

Fitting the headrest

Important!
●
To adapt it to the user, the grab handle (3,
fig. 6) can be fitted with the curve facing the
front or the back.
●
The headrest pad (10, fig. 6) can be re-
moved and replaced by other pad shapes
(optional). To remove it, loosen the retain-
ing bolts (9, fig 6).
1.
Use the star handle to insert the screw (6, fig. 6) a
little into the bracket (7, fig. 6).
2.
Push the bracket with the screw onto the handle
of the backrest (5, fig. 6) from behind in such a
way that the screw engages in the hole of the
backrest's handle.
3.
Insert the plate (4, fig. 6) into the bracket from the
front in such a way that both lugs of the plate face
down and up and the curved plate side touches
the handle of the backrest.
Important!
On inserting the retainer, the curved side of the
plate must rest entirely on the handle of the
backrest.
4.
Push the grab handle (3, fig. 6) from above into
the recesses of the bracket.
5.
Use the star handle to tighten the screw (6, fig. 6)
until the grab handle is fixed.
6.
Push the pad (10, fig. 6) and the pad holder (2,
fig. 6) into the holder (8, fig. 6) on the grab handle.
7.
Use the star handle to tighten the upper screw (1,
fig. 6) until the pad holder is fixed.
5.1.4

Attaching the chest belt

Important!
●
Attach both fastening clamps at the same
height.
●
The assembly procedure is the same for
the left and the right fastening clamp.
1.
On the backrest cover, open the belt lock of the
belt at the height where the chest belt is to be at-
tached.
2.
Feed this belt along the backrest frame and close
again.
3.
Place the inside part (4, fig. 7) of the fastening
clamp around the backrest frame.
4.
Push the outer part (2, fig. 7) of the fastening
clamp onto the internal thread (3, fig. 7) of the pin
on the inside part.
5.
Use the star handle (1, fig. 7) to attach the chest
belt (5, fig. 7) to the fastening clamp with a screw.
17