HP 316095-B21 - StorageWorks Edge Switch 2/24 릴리스 노트 - 페이지 19

{카테고리_이름} HP 316095-B21 - StorageWorks Edge Switch 2/24에 대한 릴리스 노트을 온라인으로 검색하거나 PDF를 다운로드하세요. HP 316095-B21 - StorageWorks Edge Switch 2/24 23 페이지. Edge switch release notes
HP 316095-B21 - StorageWorks Edge Switch 2/24에 대해서도 마찬가지입니다: 업데이트 매뉴얼 (9 페이지), 매뉴얼 (41 페이지), 매뉴얼 (40 페이지), 릴리스 노트 (32 페이지), 릴리스 노트 (27 페이지), 매뉴얼 (26 페이지), 릴리스 노트 (27 페이지), 릴리스 노트 (25 페이지), 설치 지침 매뉴얼 (24 페이지), 릴리스 노트 (23 페이지), 릴리스 노트 (23 페이지), 릴리스 노트 (22 페이지), 릴리스 노트 (19 페이지), 릴리스 노트 (19 페이지), 릴리스 노트 (18 페이지), 사용 설명서 (17 페이지), 릴리스 노트 (17 페이지), 업그레이드 지침 (16 페이지), 사용 설명서 (16 페이지), 설치 지침 매뉴얼 (16 페이지), 릴리스 노트 (16 페이지), 릴리스 노트 (17 페이지), 릴리스 노트 (17 페이지), 릴리스 노트 (11 페이지)

페이지 인쇄

HP 316095-B21 - StorageWorks Edge Switch 2/24 릴리스 노트

Issue

If Frame Redirection (FR) zones are being used with

M-series switches and directors and there are FR

zones loaded on all switches in the fabric, FR zones

will be lost on the M-series switches and directors

upon power cycle. When this happens, any device

that attempts to log in on any port will have the port

it uses blocked (via Event #012: "Redirect Zones

database no longer intact. Blocking all N-ports.")

The name server database sometimes may be out

of sync after power cycle of an Mi10K director in

a fabric with other switches and directors. This is

seen as a different number of entries in the

nameserver of the different switches, and could

result in devices in the fabric not establishing com-

munications with devices connected to the Mi10K

after the Mi10K completes powering up.

In Open Fabric mode, adding zone members in

Domain, Port format is not prohibited, even though

they are ignored, as only zone members in WWN

format are effective in Open Fabric mode. However,

if in Open Fabric mode and zone members in Do-

main, Port format are added, this will cause a zone

merge failure if there is an Mi10K director in the

fabric.

Invalid IP addresses can be erroneously accepted

for syslog recipients.

In a mixed fabric (M-series and B-series switches)

in McDATA Fabric interop mode, devices will be

prevented from logging in to a switch or director

that is Power On Recycled (POR) when RD Zones

are configured. This can be evidenced by the name

server database being empty and F_ports not com-

ing online.

After restoring configuration and changing domain

ID of a switch, occasionally the switch may not join

the fabric .

If an external loopback diagnostic test is run, and

the loopback plug/cable has erroneously not been

connected, and the test is stopped before it com-

pletes, then the port will be failed and become inop-

erable.

Workaround

Use one of the following workarounds:

If the switches are still in a fabric with FR zones activ-

ated, perform the CLI cfgsave command on any

Brocade switch running FOS. This will push the FR

zones to all M-series switches and directors in the

fabric.

If the switches are no longer in a fabric with FR zones

activated, run the CLI command disableSplZone-

Set on each M-series switch or director that was

power cycled to clear the invalid FR zone database.

After completing the workaround, any port with an

attached device that was blocked will become

unblocked. The device will then be allowed to login.

After power cycling an Mi10K in your fabric, check the

nameserver entries in the Mi10K and the other switches

in your fabric. Setting a discrepant switch offline and

then online will cause the nameserver databases to sync

up. This would be disruptive to devices connected to the

switch that is set offline, and should be planned for ac-

cordingly.

Do not add zone members in Domain, Port format if

operating in Open Fabric mode.

When entering an IP address for a syslog recipient, use

caution not to include invalid characters (alphabetic and

special characters).

To allow the devices to login if this occurs is to either

execute "cfgsave" from a B-series switch in the fabric,

or delete the RD zones locally using the CLI.

Taking the switch offline and then back online will allow

the switch to join the fabric. This would be disruptive to

devices connected to the switch that is set offline, and

should be planned for accordingly.

This can be avoided by allowing the test to complete,

and to be sure to use an external loopback plug/cable

when executing this test. If a port is failed in this way,

a port reset will recover the port.

Director and Edge Switch release notes (09.08.03)