HP StorageWorks 1000 - Modular Smart Array 프로그래밍 매뉴얼 - 페이지 4

{카테고리_이름} HP StorageWorks 1000 - Modular Smart Array에 대한 프로그래밍 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. HP StorageWorks 1000 - Modular Smart Array 8 페이지. Power supply, computer
HP StorageWorks 1000 - Modular Smart Array에 대해서도 마찬가지입니다: 네트워크 매뉴얼 (8 페이지), 지원 목록 (34 페이지), 오류 방지 매뉴얼 (12 페이지), 기술 백서 (12 페이지), 펌웨어 업데이트 (9 페이지), 개요 (20 페이지), 설치 매뉴얼 (2 페이지), 지원 전화번호 (19 페이지), 참조 매뉴얼 (48 페이지), 관리 매뉴얼 (40 페이지), 릴리스 노트 (13 페이지), 빠른 시작 지침 (8 페이지), 빠른 시작 매뉴얼 (7 페이지), 릴리스 노트 (5 페이지), 교체 지침 (4 페이지), 백서 (13 페이지), 기술 개요 (15 페이지), 빠른 사양 (17 페이지), 사양 (49 페이지), 시작하기 매뉴얼 (34 페이지), 설치 (4 페이지), 설치 매뉴얼 (18 페이지), 분해 지침 매뉴얼 (9 페이지)

HP StorageWorks 1000 - Modular Smart Array 프로그래밍 매뉴얼
HP 6002A/HP 1000
0044
1ERORV=1BERRC1DLU)
0045
1FC1ERORV.EQ.O) RETURN
0046
WR1TEC1LU,1000)1ERORV
0047
1000
FORMATC"HP-1B ERROR
..
13
..... )
0048
VOUT=NO
0049
RETURN
0050
300 WR1TEC1LU,1001)
0051
1001 FORMAH"6002A VOLTAGE OUT OF RANGE
.")
0052
RETURN
0053
END
Figure
9·4. Programming
6002A
Voltages
(Continued)
The range digit can be the number 1 specifying low range
(0-10 volts for CV, 0-2A for CC) or the number 2 specifying
high range (0-50 volts for CV, 0-10 amps for CC). The mag-
nitude digits can be any number from 0-999 (see figure 9-3).
Since 999 is the maximum value for the magnitude digits, the
programmable output ranges are as shown in figure
9-3.
Figure 9-4 shows a FORTRAN test program and a
generalized subroutine which allows the 6002A to be pro-
grammed from 0-49.9 volts by inputting the desired voltage
value from a user terminal. The equations required to do the
operation are straight forward and can be found in the sub-
routine.
3
Range programming for the CC operation can be
done in a similiar fashion.
The following paragraphs provide detailed operating instruc-
tions required to program the 6002A for constant voltage or
constant current operation. Refer to figures 9-5 and 9-6
for
adjustments and component locations respectively.
Low Range CV -
0 to 9.99V (99.9% of 10V)
High
Range CV -
0 to
49.95V
(99.9% of 50V)
Low Range CC -
0 to 1.998A (99.9% of 2A)
High Range CC -
0
to
9.99A (99.9% of 10A)
Figure 9·3. 6002A Programmable Output Ranges
3
See the 6002A Operating and Service Manual, Appendix
A
for
more information conceming range programming.
9·4
Constant Voltage Operation
To program the supply for constant voltage operation:
a.
Connect the supply to an HP 1000 controller.
b.
Set the mode switches on the rear of supply to the CV
'''--./
position
,
c.
Turn on the supply.
d.
With the supply's output terminals open, program the
supply for the desired output voltage.
e.
Connect a short across the supply's rear panel output
terminals and adjust the front panel current control for
the
desired maximum output current. If a load change
causes this current limit to be exceeded, the supply
automatically crosses over to constant current operation
at this preset current limit and the output voltage drops
proportionally.
Constant Current Operation
To program the supply for constant current operation, you
must first adjust HP-IB option 001 for CC operation (steps a
through h).
a,
Turn off the supply and set mode switches to the CC
position.
b.
Turn the VOLTAGE control on the front panel fully
clockwise.