HP XP20000/XP24000 구성 매뉴얼 - 페이지 26

{카테고리_이름} HP XP20000/XP24000에 대한 구성 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. HP XP20000/XP24000 46 페이지. Hp storageworks xp disk array configuration guide: vmware (a5951-96106, september 2010)
HP XP20000/XP24000에 대해서도 마찬가지입니다: 릴리스 노트 (13 페이지), 통합 매뉴얼 (29 페이지), 릴리스 노트 (4 페이지), 관리자 매뉴얼 (50 페이지), 구성 매뉴얼 (42 페이지), 구성 매뉴얼 (40 페이지), 구성 매뉴얼 (40 페이지), 구성 매뉴얼 (36 페이지), 구성 매뉴얼 (36 페이지), 구성 매뉴얼 (30 페이지), 구성 매뉴얼 (36 페이지), 릴리스 노트 (5 페이지), 구성 매뉴얼 (46 페이지), 참조 매뉴얼 (46 페이지), 구성 매뉴얼 (40 페이지), 구성 매뉴얼 (44 페이지), 구성 매뉴얼 (38 페이지), 구성 매뉴얼 (34 페이지), 구성 매뉴얼 (30 페이지), 구성 매뉴얼 (30 페이지)

페이지 인쇄

Restart the server.

To see a list of the failover devices and paths, at the server prompt enter:

list failover devices

Example failover device path listing

0x20 [V6E0-A2-D0:0] HP OPEN-3 rev:HP16

Up 0x0D [V6E0-A2-D0:0] HP OPEN-3 rev:HP16

0x1B [V6E0-A3-D0:0] HP OPEN-3 rev:HP16

0x21 [V6E0-A2-D0:2] HP OPEN-3 rev:HP16

0x0F [V6E0-A2-D0:2] HP OPEN-3 rev:HP16

0x1D [V6E0-A3-D0:2] HP OPEN-3 rev:HP16

0x22 [V6E0-A2-D0:4] HP OPEN-3 rev:HP16

0x11 [V6E0-A2-D0:4] HP OPEN-3 rev:HP16

0x1F [V6E0-A3-D0:4] HP OPEN-3 rev:HP16

0x23 [V6E0-A2-D0:1] HP OPEN-3 rev:HP16

0x0E [V6E0-A2-D0:1] HP OPEN-3 rev:HP16

0x1C [V6E0-A3-D0:1] HP OPEN-3 rev:HP16

0x24 [V6E0-A2-D0:1] HP OPEN-3 rev:HP16

0x0E [V6E0-A2-D0:3] HP OPEN-3 rev:HP16

0x1C [V6E0-A3-D0:3] HP OPEN-3 rev:HP16

Helpful Multipath commands

Other useful Multipath commands are described below.

MM Set failover priority <pathid> = <number> </insert>

This command sets the priority level for each path. The ID must be a valid path ID, and the number

must be a decimal integer value in the range 1-4,000,000, with 1 being the highest priority and

4,000,000 being the lowest priority. The default value of 0 (zero) indicates that there is no priority.

The /insert option will move the priorities on all paths that were equal or lower than <number>. For

example, if the paths had priorities of 1,2,3,4, and a new path is assigned a number 2 using the

/insert option, then the paths that were 2, 3, and 4 are moved to 3, 4, and 5, and the new path

assigned priority 2.

MM Set failover state <pathid> = <Up: Down> </setpath>

This command sets the state of the path. The ID must be a valid path ID. If the path is Up, it can be

taken offline, and will not be used to switch to. Another path will be selected. If the path is offline,

the path will be reactivated, if possible, and set to an Up state. The /setpath option will reselect the

highest priority path that is up.

MM Set failover path <pathid>

This command moves the selected path to the one specified by the path ID. The ID must be a valid

path that is up. This does not alter the priorities on the paths, and any reselection of the path may

cause the path to change. A later option will be added to reassign that path to the highest priority.

MM Restore failover path device_id

This command forces the device to reselect the highest priority path that is online. The device_id must

be a valid device ID.

Middleware configuration

Priority = 0 selected

Priority = 0

Priority = 0 selected

Priority = 0

Priority = 0 selected

Priority = 0

Priority = 0 selected

Priority = 0

Priority = 0 selected

Priority = 0