Panasonic PT-AE1000 사용 설명서 - 페이지 19
{카테고리_이름} Panasonic PT-AE1000에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Panasonic PT-AE1000 28 페이지. Panasonic lcd projector operating instructions
Panasonic PT-AE1000에 대해서도 마찬가지입니다: 사용 설명서 (28 페이지)
페이지 인쇄
POSITION Menu
|Q39aSHii
Eol
signals.
ZOOM1 =4 ZOOM2
• AUTO -4 4:3
-4
16:9-+ JUST
-4
ZOOM
NTSC signal
• 4:3 -4 16:9
• 4:3-4 16:9
VGA or SVGA signals
• Not switchable
WIDE480/600/720/768-2 signals
• 4:3 «4 16:9
• 16:9-4 H - FIT
«4
V - FIT
-4
ZOOM
1 125 (1 080)/50i,
1 125 (1 080)/60i,
1 125 (1 080)/50p,
1 125 (1 080)/60p,
1 125 (1 080)/24p, 750 (720)/50p
and 750 (720)/60p signals
• 4:3 -4 16:9 -4 JUST -4 ZOOM
525p (480p) and 625p (576p)
signals
® 4:3 -4 16:9 -4 14:9 -4 JUST
-4
ZOOM1
-4
ZOOM2
625i (576i), 625p (576p)
• auto -4 4:3
-4
16:9 -4 JUST
-4
ZOOM
525i (480i), 525p (480p)
• 16:9-4 H - FIT-4 V-FIT
1 125 (1 080)/50i,
1 125 (1 080)/60i,
1 125 (1 080)/50p,
1 125 (1 080)/60p,
1 125 (1 080)/24p, 750 (720)/50p,
750 (720)/60p signals
i Signalling) detects if a
25i (576i) signal is input and that
fication signal, and switch the aspect
tting automatically. You can switch
ually.
OVER SCAN
i nne 4 edges of an image is partly dropped, you can use
this function to adjust and project it properly.
Shrink
Enlarge
• Setting range: 0 to +10
• OVER SCAN is not available with
PC
signals.
KEYSTONE
If the projector is aligned non-perpendicularly to the
screen, or if the projection screen has an angled
surface, you can vertically correct keystone.
Image
Operation
• Setting range: -32 to 32
NOTE:
• You can correct the distortion ± 30 degrees from
the vertical plane. For a better quality image,
installing the projector with a minimum of
distortion is recommended.
• Some distortion may be retained for
Lens shift
adjustment.
• The distortion of the
Main menu
screen is not
correctable.
• The result of the keystone correction will affect on
the aspect ratio and the size of the image.
AUTO SETUP
You can adjust V - POSITION H - POSITION DOT
CLOCK and CLOCK PHASE automatically when
connecting via PC. Press ENTER to adjust these at the
same time.
LENS CONTROL Menu
ZOOM/FOCUS
You can use the 2 different test patterns to adjust the focus and zoom of the image. See "Lens shift and positioning
on page 16.
1.
Press ENTER to display test pattern 1.
•
Press A f to adjust the focus and < ► to adjust the zoom.
2.
Press ENTER to display test pattern 2.
•
Press A ▼ to adjust the focus and ◄ ► to adjust the zoom.
3.
Press ENTER to display the projected image.
• You can confirm the adjustment is fit to the projected image.
4.
Press MENU or RETURN to return to the previous menu, or press repeatedly to escape the menu mode.
NOTE:
• When the projector and/or the screen is tilted, adjust the focus at the centre of the image. The upper and
lower edge might be out of focus.
• When the image is distorted in keystone, adjust the KEYSTONE in POSITION menu.