Panasonic PT-AE1000 사용 설명서 - 페이지 21
{카테고리_이름} Panasonic PT-AE1000에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Panasonic PT-AE1000 28 페이지. Panasonic lcd projector operating instructions
Panasonic PT-AE1000에 대해서도 마찬가지입니다: 사용 설명서 (28 페이지)
페이지 인쇄
I
o
3
A)
3
O
o
TEMP and LAMP Indicators
Controlling alerts
If a problem should occur with the projector thp
tfmp
annw i a mm •
A
...
,
as follows.
P jecior, tne rfcMP and/or LAMP indicators will alert you. Respond to the alert
1.
Confirm the POWER indicator status and turn off the projector in the proper way.
2.
Find out the cause of the problem.
3.
Follow the instructions for each indication below and solve the problem.
4.
Turn on the projector in the correct way and confirm the indicator is not indicating a problem any longer.
NOTE:
~~
------
* Se"ice°CemreS f°Un<1"
Pr°blem rel™inS' d° not turn on the pro'ec,or lns,ead ""tact an Authorised
LAMP indicator
TEMP indicator
I TEMP indicator
P
I
• Illuminating RED and still projecting
• Flashing RED and POWER is turned off
The temperature inside and/or outside the projector is abnormally high.
The ventilation ports are
covered.
The room temperature is too
The Air fi,ter is excessively
high.
dirty and the ventilation is
_poor.
Remove the object(s) from
Reinstall the projector at a
~Clean or replace the
AirfilteT
the ventilation ports or clear
temperature controlled place
in the proper way- See
around the projector.
See "Setting up" on page 14
"Cleanin9 the Air filter" on
LAMP indicator
page 41.
• Illuminating RED
LAMP RUNTIME has reached 1 800 hours
(with LAMP POWER set to NORMAL),
Lamp unit will run out soon and needs to be
replaced.
Replace the Lamp unit. See "Before
replacing the Lamp unit" on page 42.
• Flashing RED
LAMP circuit failure, abnormal functiorToT"
LAMP is damaged.
The projector is switched off incorrectly.
• Let the LAMP cool down and turn on the
projector.
• If the POWER does not turn on, contact an
Authorised Service Centre
Care and Replacement
Before cleaning
• Ensure the projector is switched off.
• Unplug all the cables from the projector.
Cleaning your projector
| Cleaning the outer surface of the projector
Wipe off dirt and dust gently with a soft cloth.
•
if it is difficult to remove the dirt, soak a cloth in a neutral detergent diluted with water, wring the cloth well
and then wipe the projector. Dry off the projector with dry cloth.
•
If you use a chemical treated wipe, follow the instructions supplied with it,
| Cleaning the lens surface
Wipe off dirt and dust gently with a lint-free cloth.
•
Make sure no dirt or dust remains on the surface of the lens. It will be enlarged and projected onto a
screen.
| Cleaning the Air filter
If the Air filter is excessively dirty, the internal temperature of the projector increases and may cause
malfunction. Clean the Air filter regularly every 100 hours of usage.
1.
Place a finger at the bottom of the Air filter.
2.
Slightly push up and pull out the Air filter to remove.
.
3.
Vacuum dirt and dust from the Air filter.
•
Do not wash the Air filter
4.
Place and slightly slide in the Air filter in the Air intake port to attach.
•
Make sure the Air filter clicks into the place.
NOTE:
• Do not use the projector without attaching the Air filter,
| Replacing the Air filter
The Air filter should be replaced when cleaning is ineffective and when replacing the Lamp unit. An
replacement Air filter is provided with a replacement lamp unit, ET-LAE1000. Contact an Authorised Service
Centre for the optional Air filter.