Panasonic PT-AE700 사용 설명서 - 페이지 23
{카테고리_이름} Panasonic PT-AE700에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Panasonic PT-AE700 32 페이지. Panasonic lcd projector operating instructions
페이지 인쇄
Adjusting the position
When the input signal is from a
PC, first select "AUTO SETUP"
and then press the ENTER button
to initiate automatic positioning.
If the optimum setting is not
obtained when "AUTO SETUP" is
carried out, adjust by the following
procedure.
Press the F or G button to select
an item, and then press the I or H
button to change the setting.
For items with bar scales, press the
ENTER button or the I or H button
to display the adjustment screen,
and then Press the I or H button
to make the adjustment.
When an S-VIDEO/VIDEO/SCART/
HDMI signal is being input
P O S I T I O N
H - P O S I T I O N
0
V - P O S I T I O N
0
A S P E C T
1 6 : 9
S E L E C T
E N T E R
E S C
When a YP
P
signal is being input
B
R
P O S I T I O N
H - P O S I T I O N
0
V - P O S I T I O N
0
C L O C K P H A S E
0
A S P E C T
4 : 3
S E L E C T
E N T E R
E S C
When a PC signal is being input
P O S I T I O N
H - P O S I T I O N
0
V - P O S I T I O N
0
D O T C L O C K
0
C L O C K P H A S E
0
A S P E C T
4 : 3
A U T O S E T U P
S E L E C T
E N T E R
E S C
44-E
NGLISH
Horizontal position
(H-POSITION)
To move the picture to the left: I button
To move the picture to the right: H button
Vertical position
(V-POSITION)
To move the picture down: I button
H button
To move the picture up:
DOT CLOCK
(PC only)
Periodic striped pattern interference
(noise) may occur when a striped
pattern such as the one below is
projected. If this happens, press the
I or H button to adjust so that any
such noise is minimised.
CLOCK PHASE
(PC/YP
P
only)
B
R
Adjust the "DOT CLOCK" setting first
before carrying out this adjustment.
Press the I or H button to adjust
so that the noise level is least
noticeable.
NOTE:
B If signals with a dot clock
frequency of 100 MHz or higher
are being input, interference
may not be completely
eliminated when the "DOT
CLOCK" and "CLOCK PHASE"
adjustments are carried out.
B When YP
P
signals are being
B
R
input, "CLOCK PHASE" can be
adjusted only when
1 125 (1 080)/60i, 1 125
(1 080)/50i, 750 (720)/60p or 750
(720)/50p signals are being input.
ASPECT
Refer to page 30.
Turning off the picture momentarily
(SHUTTER)
The "SHUTTER" function can be used to momentarily turn off the picture
when the projector is not being used for short periods of time. The projector
uses less power in "SHUTTER" mode than it does in normal projection
mode.
# Select "SHUTTER" from the "MAIN MENU" and then press the
ENTER button.
$ Press any button on either the projector or remote control unit
(except the LIGHT button) to return to normal operating mode.
Changing the display language
# Select "LANGUAGE" from the "MAIN MENU" and then press the
ENTER button.
$ Press the F or G button to select a language and then press the
ENTER button.
L A N G U A G E
E N G L I S H
E N G L I S H
D E U T S C H
F R A N Ç A I S
E S P A Ñ O L
I T A L I A N O
S E L E C T
E N T E R
E S C
AUTO SETUP
(PC only)
"H-POSITION", "V-POSITION",
"DOT CLOCK" and "CLOCK
PHASE" are automatically adjusted
according to the input signal.
NOTE:
B When the "ASPECT" is set to
"V SCROLL" (page 30), "AUTO
SETUP" cannot be performed.
Indicates the language which is
currently set
E
-45
NGLISH