Panasonic DVD-CV37 사용 설명서 - 페이지 19

{카테고리_이름} Panasonic DVD-CV37에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Panasonic DVD-CV37 24 페이지. Dvd/cd player
Panasonic DVD-CV37에 대해서도 마찬가지입니다: 사용 설명서 (24 페이지), 사용 설명서 (32 페이지), 사용 설명서 (29 페이지), 빠른 매뉴얼 (2 페이지), 사용 설명서 (24 페이지)

페이지 인쇄

Troubleshooting guide

Before requesting service, make the below checks. If you are in doubt about some of the check points, or if the remedies indicated in the chart do not

solve the problem:

In the U.S.A., contact the Panasonic Customer Call Center at 1-800-211-7262, or e-mail [email protected], or web site

(http://www.panasonic.com).

In Canada, contact Panasonic Canada Inc. Customer Care Centre at 1-800-561-5505, web site (www.panasonic.ca), or an authorized

Servicentre closest to you.

Power

No power.

The unit is automatically

switched to the standby mode.

Operation

No response when buttons

pressed.

No operations can be performed

with the remote control.

Play fails to start even when

[1] (PLAY) is pressed.

Play starts but then stops

immediately.

Cannot play DVD

Alternative languages fail to be

selected.

No menu play.

No subtitles.

Soundtrack and/or subtitle

language is not the one selected

with the SETUP menus.

Angle cannot be changed.

Dialogue Enhancer has no effect.

You have forgotten your ratings

password.

Reset all the settings to Factory

Preset.

The drawer stops while

opening.

Sound

No sound.

Distorted sound.

Piercing noise comes from the

speakers.

≥Insert the AC power supply cord securely into the household AC outlet.

≥To conserve power, the unit automatically switches to standby after approximately 30 minutes in

the stop mode. Turn the power back to ON.

≥The unit was switched to standby by the SLEEP timer.

≥Some operations may be prohibited by the disc.

≥The unit may not be operating properly due to lightning, static electricity or some other external

factor.

Reset procedure:

Press [POWER Í] to switch the unit to the standby mode and then back to ON.

Alternatively, press [POWER Í] to switch the unit to the standby mode, disconnect the AC power

supply cord, and then reconnect it.

≥Check the batteries are installed correctly.

≥The batteries are depleted: Replace them with new ones.

≥Point the remote control at the remote control signal sensor and operate.

≥Condensation has formed: Wait 1 to 2 hours for it to evaporate.

≥This unit cannot play discs other than DVD, CD and Video CD.

≥You can only play DVD if their region number is "1", "ALL" or multiple region number

including "1".

≥The disc may be dirty and may require cleaning.

≥Ensure that the disc is installed with the label of the side to be played facing upwards.

≥The sequential mode is on. Press [SEQUENTIAL] ([CD SEQUENTIAL]) to turn the sequential

mode off.

≥An alternative language is not selected with discs which do not contain more than one language.

≥In the case of some discs, the alternative language cannot be selected with [AUDIO] or

[SUBTITLE]. Try selecting it from the disc's menu if one is available.

≥Menus are only displayed if they are recorded on the disc.

≥Subtitles appear only with discs that contain them.

≥Subtitles are cleared from the television. Display the subtitles.

≥The language is not recorded on the disc.

≥This function is dependent on software availability. Even if a disc has a number of angles

recorded, these angles may be recorded for specific scenes only.

≥This feature does not work when the unit is outputting bitstream signals.

≥While stopped, press and hold [: 6] and [;] on the unit and then also press and hold [<]

on the unit until "Initialized" disappears from the television. Turn the unit off and on again.

All settings will return to the default values.

≥If possible, remove the discs at the front of the drawer, then turn the unit off and back on again.

≥Check the connections.

≥Check the volume on the equipment you have connected.

≥Ensure that the input settings for the television and stereo system are correct.

≥Turn ADVANCED SURROUND off if it causes distortion.

≥If you have connected this unit to other equipment through the DIGITAL AUDIO OUT terminal,

ensure you have selected the correct settings for "Dolby Digital", "DTS Digital Surround" in the

SETUP menu's Audio menu.

Page

–

Cover

page

–

6, 18

–