Panasonic DVD-CV37 Gebruiksaanwijzing - Pagina 19
Blader online of download pdf Gebruiksaanwijzing voor {categorie_naam} Panasonic DVD-CV37. Panasonic DVD-CV37 24 pagina's. Dvd/cd player
Ook voor Panasonic DVD-CV37: Gebruiksaanwijzing (24 pagina's), Gebruiksaanwijzing (32 pagina's), Gebruiksaanwijzing (29 pagina's), Beknopte handleiding (2 pagina's), Gebruiksaanwijzing (24 pagina's)
Pagina afdrukken
Troubleshooting guide
Before requesting service, make the below checks. If you are in doubt about some of the check points, or if the remedies indicated in the chart do not
solve the problem:
In the U.S.A., contact the Panasonic Customer Call Center at 1-800-211-7262, or e-mail [email protected], or web site
(http://www.panasonic.com).
In Canada, contact Panasonic Canada Inc. Customer Care Centre at 1-800-561-5505, web site (www.panasonic.ca), or an authorized
Servicentre closest to you.
Power
No power.
The unit is automatically
switched to the standby mode.
Operation
No response when buttons
pressed.
No operations can be performed
with the remote control.
Play fails to start even when
[1] (PLAY) is pressed.
Play starts but then stops
immediately.
Cannot play DVD
Alternative languages fail to be
selected.
No menu play.
No subtitles.
Soundtrack and/or subtitle
language is not the one selected
with the SETUP menus.
Angle cannot be changed.
Dialogue Enhancer has no effect.
You have forgotten your ratings
password.
Reset all the settings to Factory
Preset.
The drawer stops while
opening.
Sound
No sound.
Distorted sound.
Piercing noise comes from the
speakers.
≥Insert the AC power supply cord securely into the household AC outlet.
≥To conserve power, the unit automatically switches to standby after approximately 30 minutes in
the stop mode. Turn the power back to ON.
≥The unit was switched to standby by the SLEEP timer.
≥Some operations may be prohibited by the disc.
≥The unit may not be operating properly due to lightning, static electricity or some other external
factor.
Reset procedure:
Press [POWER Í] to switch the unit to the standby mode and then back to ON.
Alternatively, press [POWER Í] to switch the unit to the standby mode, disconnect the AC power
supply cord, and then reconnect it.
≥Check the batteries are installed correctly.
≥The batteries are depleted: Replace them with new ones.
≥Point the remote control at the remote control signal sensor and operate.
≥Condensation has formed: Wait 1 to 2 hours for it to evaporate.
≥This unit cannot play discs other than DVD, CD and Video CD.
≥You can only play DVD if their region number is "1", "ALL" or multiple region number
including "1".
≥The disc may be dirty and may require cleaning.
≥Ensure that the disc is installed with the label of the side to be played facing upwards.
≥The sequential mode is on. Press [SEQUENTIAL] ([CD SEQUENTIAL]) to turn the sequential
mode off.
≥An alternative language is not selected with discs which do not contain more than one language.
≥In the case of some discs, the alternative language cannot be selected with [AUDIO] or
[SUBTITLE]. Try selecting it from the disc's menu if one is available.
≥Menus are only displayed if they are recorded on the disc.
≥Subtitles appear only with discs that contain them.
≥Subtitles are cleared from the television. Display the subtitles.
≥The language is not recorded on the disc.
≥This function is dependent on software availability. Even if a disc has a number of angles
recorded, these angles may be recorded for specific scenes only.
≥This feature does not work when the unit is outputting bitstream signals.
≥While stopped, press and hold [: 6] and [;] on the unit and then also press and hold [<]
on the unit until "Initialized" disappears from the television. Turn the unit off and on again.
All settings will return to the default values.
≥If possible, remove the discs at the front of the drawer, then turn the unit off and back on again.
≥Check the connections.
≥Check the volume on the equipment you have connected.
≥Ensure that the input settings for the television and stereo system are correct.
≥Turn ADVANCED SURROUND off if it causes distortion.
≥If you have connected this unit to other equipment through the DIGITAL AUDIO OUT terminal,
ensure you have selected the correct settings for "Dolby Digital", "DTS Digital Surround" in the
SETUP menu's Audio menu.
Page
6
–
10
–
–
6
6
5
–
5
Cover
page
–
–
8
–
8
–
–
13
–
13
–
–
–
6, 18
–
–
12
17
19