Epever LS LPLI Series 매뉴얼 - 페이지 2
{카테고리_이름} Epever LS LPLI Series에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epever LS LPLI Series 2 페이지. Solar charge controller with built-in led driver
페이지 인쇄
HUIZHOU EPEVER TECHNOLOGY CO., LTD.
Timer3
LED Rated Current Percentage
Timer4/5
LED Rated Current Percentage
Timer6
LED Rated Current Percentage
※
Modify the default value according to the user's requirement.
4) Time Control
Control the load on/off time by setting the real-time clock.
5) Intelligent Power Mode
When the battery voltage goes lower than the "Reduce Power Start Voltage (adjustable),"
the intelligent power reduction mode is enabled. The LED output current is automatically
reduced in linear with the battery's voltage drop. When the battery voltage goes lower than
the "Reduce Power End Voltage (adjustable)," the LED output current is 2% of the rated
load current. The minimum percentage can be set to 1%). Also, when the battery voltage is
higher than "Reduce Power Start Voltage," the controller exits the intelligent power
reduction mode.
In the mode of Light ON/OFF and Light ON/Timer, the load is turned on
after a 1-minute delay，the delay time can be set.
The controller's real-time clock is an analog clock, valid at power-on and
invalid after power-off. When using the time mode, the clock needs to be
CAUTION
calibrated by handheld devices. Do not power off the controller after
calibration.
6. Setting Operation
There are two methods to check and set the controller's
parameters:
1) IR Remote Controller—RC-10
2) Super Parameter Programmer—FC-01
This method can realize one-key setting operation which is
suitable for bulk quantity products setting or applied in the
projects.
NOTE: Please refer to the user manual of handheld device.
7. Protection
Protection
When the battery is correctly connecting,
PV Reverse Polarity
the PV can be reversed.
When the PV is not connected, or the
connection is reversed, the battery can be
Battery Reverse
reversed.
WARNING: Controller is damaged when
Polarity
the PV connection is correct, and the
battery connection is reversed!
Battery Over Voltage
The battery voltage reaches the OVD
Battery Over Discharge
The battery voltage reaches the LVD
The temperature sensor is higher than 65℃
Battery Overheating
The temperature sensor is less than 55℃
The temperature sensor is less than the
low-temperature value
Li-battery Low
★
Temperature
The temperature sensor is higher than the
low-temperature value
Load current ≥2.5 times rated current
In one short circuit, the output is OFF 5s;
Two short circuits, the output is OFF 10s;
Load Short Circuit
Three short circuits, the output is OFF 15s;
Four short circuits, the output is OFF 20s;
Five short circuits, the output is OFF 25s;
Six short circuits, the output is OFF
Max. load voltage≥68V
One open circuit, the output is OFF 5s;
Two open circuits, the output is OFF 10s;
Load Open
Three open circuits, the output is OFF 15s;
Circuit(Load over
Four open circuits, the output is OFF 20s;
voltage)
Five open circuits, the output is OFF 25s;
Six open circuits, the output is OFF 5s;
Seven open circuits, the output is OFF 5s
★ If selecting a lithium battery, set the low-temperature value(LTV) according to the
specification; otherwise, the lithium battery is damaged.
8. Troubleshooting
Faults
Possible reasons
Charging LED
indicator off during
PV
daytime when
array disconnection
sunshine falls on PV
modules properly
Min.9V can start up the
No LED indicator
controller.
Battery LED
indicator green Fast
Battery over voltage
Flashing
Battery
Battery LED
indicator red
over discharged
Battery Status LED
red indicator
Battery Overheating
flashing
All the LED indicator
System voltage error
flashing(battery red
2H
0H
00:00—23:59H
50%
0%
0—100%
0H
0H
00:00—23:59H
0%
0%
0—100%
0H
2H
00:00—23:59H
0%
100%
0—100%
Conditions
The controller is
no damage
Stop charging
Stop discharging
Output is OFF
Output is ON
Stop charging or
discharge
Begin charging
or discharge
Output is OFF
Clear the fault:
Restart the
controller or
wait for one
night-day cycle
(night time>3
hours).
Output is OFF
(Cycle to
perform)
Troubleshooting
Confirm that PV and battery wire
connections are correct and tight
Measure the battery voltage with a
multi-meter. Min.9V can start up the
controller.
①Disconnect the solar array and
measure the battery voltage; ②
Change the controller; ③ Change
the battery
When the battery voltage is restored
to or above setpoint (low voltage
①
reconnect voltage), the load work
The controller automatically stops
working. When the temperature is
below 50 º C, the controller resumes
Check whether the battery voltage
matches the controller's working
3
Tel：+86-10-82894896/82894112/+86-752-3889706
indicator flashing)
Powering on
normally, the load is
off
The dimming
function is invalid
① When the battery is over discharged, the battery indicator will be red. The load will be off
all the time before the voltage is more than the Low Voltage Reconnect Voltage (LVRV). To
judge the system is normal or not, firstly measuring the battery voltage, whether it is more
than LVRV; if not, restarting the controller to detect the load.
The LVRV can be set, but it must be done carefully to avoid damaging the
battery if the LVRV is set too low.
WARNING
9. Technical Specifications
Models
Item
Nominal system
voltage
Rated charge current
Max. PV open circuit voltage
Battery input voltage range
Max. output power
Max. output Current
Output voltage range
Status
Load open circuit voltage
Maximum output efficiency
Output current
control accuracy
Battery Type
Equalization Voltage▼
Boost Voltage▼
Float Voltage▼
Reduce Power Start
Voltage ▼
Reduce Power End
Voltage ▼
Low Voltage
Reconnect Voltage▼
Low Voltage Disconnect
Voltage▼
Boost Voltage▼
Reduce Power Start
Voltage ▼
Reduce Power End
Voltage ▼
Low Voltage
Reconnect Voltage▼
Low Voltage Disconnect
Voltage▼
Self-consumption
Charge Circuit Voltage Drop
Com. way
Com. distance of IR
Working environment
temperature
Enclosure
Overall dimension(mm)
Mounting dimension(mm)
Mounting hole size(mm)
Power cable
Net weight
◆ When selecting a lithium battery, the controller cannot automatically recognize
the nominal system voltage and has no temperature compensation.
▼ The parameters are the 12V system at 25 º C, double the values in the 24V system.
10. Disclaimer
This warranty does not apply under the following conditions:
Damage from improper use or use in an unsuitable environment.
PV or load current, voltage, or power is exceeding the rated value of the controller.
The controller's working temperature exceeds the limit working temperature.
User disassembly or attempted to repair the controller without permission.
The controller is damaged due to natural elements such as lighting.
The controller is damaged during transportation and shipment.
voltage. Please change to a suitable
battery or reset the working voltage
①The connecting
①Check the connecting cables
②Check the load mode and
wires are error or
virtual connection
parameter
②Load mode is wrong
③The voltage of the LED light source
③The controller does
is not in the output voltage range of
not match with the LED
the controller
④Check the connecting cables and
light.
④Output short circuit
LED light source
The controller does not
①Replace the LED light
match with the LED
②Reduce system rated voltage
light source. This
product is a step-up
grade, and replace the product model
current control; if the
For example, switch the 24V system
input voltage is lower
to the 12V system, and replace the
than the rated voltage,
corresponding controller.
it is not working.
LS101240LPLI LS101260LPLI
12VDC
10A
10A
30V
9～16V
40W/12V
60W/12V
2.6A
4.0A
(Max. Battery Voltage +2V)～60V
Lead-acid battery: Sealed(default)/Gel/Flooded/User
Lithium battery:LiFePO4/Li-NiCoMn/User
Sealed:14.6V; Flooded:14.8V;User:9-17V
Sealed:14.4V;Gel:14.2V;Flooded:14.6V;User:9-17V
Sealed/Gel/Flooded：13.8V; User：9-17V
Sealed/Gel/Flooded：12.2V; User：9-17V
Sealed/Gel/Flooded：12.0V; User：9-17V
Sealed/Gel/Flooded：12.6V; User：9-17V
Sealed/Gel/Flooded：11.1V; User：9-17V
LiFePO4(4s):14.5V/Li-NiCoMn(3s):12.5V/User:9-17V
LiFePO4(4s):12.8V/Li-NiCoMn(3s):12.2V/User:9-17V
LiFePO4(4s):12.0V/Li-NiCoMn(3s):10.5V/User:9-17V
LiFePO4(4s):12.8V/Li-NiCoMn(3s):10.5V/User:9-17V
LiFePO4(4s):11.1V/Li-NiCoMn(3s):9.3V/User:9-17V
≤18mA(12V);≤23mA(24V)
-40℃～+55℃
IP68(1.5m,72h)
87x63x24.8
87x60x22.8
80
80
Φ4
Φ4
PV/BAT:14AWG/2.5mm
LOAD: 18AWG/1.0mm
0.18kg
0.21kg
Any changes without prior notice!
4
Website：www.epever.com
LS102460LPLI
LS2024120LPLI
12/24VDC◆
10A
20A
50V
9～32V
30W/12V
60W/12V
60W/24V
120W/24V
2.0A
4.0A
60V
96%
≤2%
≤0.14V
IR
＜6m
87x63x24.8
108.5x88x25.6
80
100.5
Φ4
Φ5
PV/BAT:
2
2
12AWG/4.0mm
2
LOAD:
2
18AWG/1.0mm
0.21kg
0.40kg
Version number：V2.2