Epever Tracer3910BPL 빠른 매뉴얼 - 페이지 2

{카테고리_이름} Epever Tracer3910BPL에 대한 빠른 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epever Tracer3910BPL 2 페이지. Mppt solar charge controller
Epever Tracer3910BPL에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (3 페이지), 빠른 시작 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (2 페이지)

페이지 인쇄

6. Accessories(optional) and Software

Software

(1)Solar station Monitor

 Download software

www.epsolarpv.com/en/index.php/Technical/download——PC Software for the Solar

Charge Controller

(2)Mobile APP software setting

 Download software

www.epsolarpv.com/en/index.php/Technical/download——Andriod

Li-Battery Solar Charge Controller

 IPhone——APP Store——EPEVER

※Specific instructions refer to the list of accessories and software.

7. Protection

Protection

Conditions

PV Reverse

When the battery is correct connecting, the

Polarity

PV can be reversed.

Battery

When the PV is not connecting, the battery

Reverse

can be reversed.

Polarity

Battery Over

The battery voltage reaches to the OVD

Voltage

Battery Over

The battery voltage reaches to the LVD

Discharge

Temperature sensor is higher than 65℃

Battery

Overheating

Temperature sensor is less than 55℃

Temperature sensor is less than the low

Lithium battery

temperature value(Default 0℃)

Low

Temperature sensor is higher than the low

Temperature

temperature value(Default 0℃)

Load current ≥2.5 times rated current

One short circuit, the output is OFF 5s;

Two short circuit, the output is OFF 10s;

Load Short

Three short circuit, the output is OFF 15s;

Circuit

Four short circuit, the output is OFF 20s;

Five short circuit, the output is OFF 25s;

Six short circuit, the output is OFF

Lithium battery

Limit current temperature

limit current in

T1＞T2＞T3＞T4＞T5＞T6

low

Limit current I1＞I2＞I3＞I4＞I5＞I6

temperature

8. Technical Specifications

Item

Nominal system voltage

Battery input voltage range

Rated charge current★

Rated charge power

①

Max. PV open circuit voltage

MPP Voltage range

Max. output current

Max. output power

Output voltage range

Load open circuit voltage

Load over voltage protection

Maximum output efficiency

Output current control accuracy

Battery Type

Equalize Charging Voltage

Boost Charging Voltage

Float Charging Voltage

Low Voltage Reconnect Voltage

Low Voltage Disconnect Voltage

Boost Charging Voltage

Low Voltage Reconnect Voltage

Low Voltage Disconnect Voltage

Self-consumption

Temperature compensation coefficient

Communication

Working environment temperature

Enclosure

Overall dimension

Mounting hole size

Mounting dimension

Power cable

Net weight

★The controller has the limit charge current function, the current can be set via the APP software and RC10.

BEIJING EPSOLAR TECHNOLOGY CO., LTD.

APP

Status

The controller is not

damage

Stop charging

stop discharging

Output is OFF

Output is ON

Lithium battery stop

charging/discharging

Lithium battery

charging

Output is OFF

Clear the fault:

Restart the controller

or wait for one

night-day cycle (night

time>3 hours).

When the temperature

is lower than T1, the

charging current is I1;

when the temperature

is lower than T2, the

charging current is I2;

and so on. However,

when the temperature

rises gradually from T4

to T1, it is performed at

I4.

Tracer2606BPL

Tracer3906BPL

12/24VDC Auto(Lithium battery do not automatic identification system voltage)

10A

15A

130W/12V;260W/24V 195W/12V;390W/24V 260W/12V;520W/24V 130W/12V;260W/24V

58V( at minimum operating environment temperature ）

46V( at 25℃ environment temperature )

( Battery voltage+2V)～36V

3.3A

4.5A

100W

130W

( Max. battery voltage+2V)～58V

58V

63V

Lead-acid battery: Sealed(Default) / Gel / Flooded/User; Lithium battery:LiFePO4/ Li-NiCoMn/User

124×89×30mm

150×93.5×32.7mm

88×76mm

120×83mm

PV/BAT:14AWG(2.5mm

0.54kg

0.73kg

Tel：+86-10-82894112 / 82894962 Website：www.epsolarpv.com/www.epever.com

9. Troubleshooting

Faults

LED Charging

indicator turn off

during daytime

when sunshine falls

on PV modules

properly

No LED indicator

Battery LED

indicator green fast

Flashing

Battery LED

indicator red

for

the

Battery LED

indicator red

flashing

Powering on

normally, the load is

off

The dimming

function is invalid

①When the battery is over discharged, the battery indicator will be red and the load will

be off all the time before the voltage is more than the Low Voltage Reconnect Voltage

(LVRV). In order to judge the system is normal or not, firstly measuring the battery

voltage whether is more than LVRV, if not, restarting the controller to detect the load

whether it is normal.

NOTE: The LVRV can be set, but it must pay more attention that it maybe

damages the battery if the LVRV is too low.

10. Disclaimer

This warranty does not apply under the following conditions:

 Damage from improper use or use in an unsuitable environment.

 PV or load current, voltage or power exceeding the rated value of controller.

 The controller is working temperature exceed the limit working environment

temperature.

 User disassembly or attempted repair the controller without permission.

 The controller is damaged due to natural elements such as lighting.

 The controller is damaged during transportation and shipment.

Tracer5206BPL

9～32VDC

20A

6.6A

200W

96%

≤2%

Sealed :14.6V/Gel：No / Flooded:14.8V/User:9-17V (×2/24V)

Sealed :14.4V/Gel：14.2V/Flooded:14.6V/User:9-17V (×2/24V)

Sealed/Gel/Flooded:13.8V/User:9-17V (×2/24V)

Sealed/Gel/Flooded:12.6V/User:9-17V (×2/24V)

Sealed/Gel/Flooded:11.1V/User:9-17V (×2/24V)

LiFePO4:14.5V/ Li-NiCoMn:12.5V / User:9-17V (×2/24V)

LiFePO4:12.8V / Li-NiCoMn:10.5V / User:9-17V (×2/24V)

LiFePO4:11.1V / Li-NiCoMn:9.3V / User:9-17V (×2/24V)

≤15mA/12V;≤22mA/24V

-3mV/℃/2V(Lithium battery don't have temperature compensation coefficient)

RS485

-40℃～+60℃

IP67

153×105×52.1mm

Φ3.5mm

120×94mm

);LOAD:18AWG(1.0mm

)

1.18kg

Possible reasons

Confirm that PV and battery wire

array disconnection

connections are correct and tight

Measure battery voltage with the

Battery voltage maybe

multi-meter. Min.9V can start up the

less than 9V

controller

Check if battery voltage is higher

Battery over voltage

than OVD, and disconnect the PV

When the battery voltage is restored

Battery

to or above LVR point (low voltage

①

reconnect voltage), the load will

over discharged

recover

The controller will automatically turn

the system off. But while the

Battery Overheating

temperature decline to be below 50

º C, the controller will resume.

①The connecting

① Check the connecting cable.

wires are error or

② Check the load's mode and

virtually connected

parameters.

②Load mode is not

③The voltage of LED light is not

appropriate.

within the output voltage range of

③This controller does

controller.

not match with the LED

④Check the connecting cables and

light.

LED light.

④Output short circuit.

The controller does not

①Replace the LED light

match with the LED

②Reduce system rated voltage

light source. This

grade and replace the product

product is a step-up

model

voltage control, If input

For example 24V system change to

voltage is lower than

12V system, and replace the

the rated voltage, it is

corresponding controller

not working.

Tracer2610BPL

Tracer3910BPL

10A

15A

195W/12V;390W/24V

95V( at minimum operating environment temperature ）

92V( at 25℃ environment temperature )

( Battery voltage+2V)～72V

3.3A

4.5A

100W

130W

( Max. battery voltage+2V)～80V

80V

100V

124×89×30mm

150×93.5×32.7mm

88×76mm

120×83mm

PV/BAT:12AWG(4mm

0.54kg

0.73kg

Any changes without prior notice! Version number：V2.0

Troubleshooting

Tracer5210BPL

20A

260W/12V;520W/24V

6.6A

200W

153×105×52.1mm

120×94mm

);LOAD:16AWG(1.5mm

)

1.18kg