Olympus BX-FLA 사용 설명서 - 페이지 2

{카테고리_이름} Olympus BX-FLA에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Olympus BX-FLA 46 페이지. Reflected light fluorescence attachment

Olympus BX-FLA 사용 설명서
BX-FLA
This unit employs
a UIS (universal
infinity
system)
optical
design,
and should
be used only with
UIS eyepieces,
objectives,
and condensers.
Less than
optimum
performance
may
result
if
inappropriate
accessories
are used.
L
J
The universal reflected light fluorescence vertical illuminator features interchangeable
cubes to employ excitation
light of different wavelengths.
If also allows combined or alternating reflected light fluorescence
and transmitted
white light observations.
1. Reflected
light fluorescence
+ transmitted
light phase contrast.
2. Reflected light fluorescence
+ transmitted
light Nomarski differential
interference
contrast.
3. Reflected
light fluorescence
+ transmitted
light brightfield
or darkfield.
By mounting standard cubes for reflected light observation, the following observation methods become possible.
1. Reflected
light brightfield/darkfield
observation.
2. Reflected light Nomarski differential
interference
contrast.
3. Reflected
light simple polarized light observation.
This instruction
manual consist of two parts: I. Reflected
Light Fluorescence
Observation
and II. Reflected
Light Observation
Modes. Use these headings to find the relevant page with the instructions
for the particular
observation
mode.
a
Getting
Ready
I. A vertical illuminator
is delicate. Handle it carefully, and avoid jolts.
2. The high pressure
mercury burner used in the unit should be a USH102 (mfd. by Ushio Electric). The
halogen lamp used in the unit should be a 12V, IOOWHAL halogen bulb (Philips 7724).
3. Verify that the burner is installed correctly and that all cords are properly connected.
4. The ultraviolet rays emitted by the burner are harmful. Be sure to use a UV protective
shield with the unit.
(See page 9.)
5. Do not open the lamp housing while the burner is turned on or for at least 10 minutes after it is turned
off. The lamp housing inside is extremely
hot and will cause injury if touched. (See page 11.)
6. The power supply unit contains high voltage components.
Do not attempt
to disassemble
it.
7. Always ground
the unit.
8. Before opening the lamp housing for replacement
of the burner or other, turn off the main switch and
unplug the power output connector from the power unit. Wait for more than 10 minutes for the burner and
lamp socket to cool down.
9. Before plugging in the mains power cord, make sure that the main switch on the power supply unit is
turned off.
1. Clean all glass components
by wiping gently with gauze. To remove fingerprints
or oil smudges, wipe with
gauze slightly moistened
with a mixture of ether (70%) and alcohol (30%).
A Since solvents
such as ether and alcohol are highly flammable,
they must be handled
carefully.
Be
sure to keep these chemicals
away from open flames or potential
sources of electrical
sparks - for
example,
electrical
equipment
that is being switched
on or off. Also remember
to always use these
chemicals
only in a well-ventilated
room.
2. Do not disassemble
any part of the attachment.
3. The burner has a service life period of 200 hours. When the hour counter on the power supply unit indicates
200 hours, replace the burner with a new one. (See page 8.)
4. When not using the unit, cover it with the dust cover provided and store it in a dry place to prevent mold
formation.
5. If a dichroic mirror cube is not to be used for a while, place it in its container and store it in a safe place.