Axor Citterio Showerpipe 180 1jet 39671009 사용 설명서 지침 - 페이지 2

{카테고리_이름} Axor Citterio Showerpipe 180 1jet 39671009에 대한 사용 설명서 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Axor Citterio Showerpipe 180 1jet 39671009 12 페이지.

페이지 인쇄

0 2

S A F E T Y N O T E S

Gloves should be worn during installation to prevent crushing and cutting injuries.

The product may only be used for bathing, hygienic and body cleaning purposes.

The arm of the shower head is intended only to hold the shower head. Do not load

it down with other objects!

Children as well as adults with physical, mental and/or sensoric impairments must

not use this product without proper supervision. Persons under the influence of

alcohol or drugs are prohibited from using this product.

Do not allow the streams of the shower touch sensitive body parts (such as your

eyes). An adequate distance must be kept between the shower and you.

The product may not be used as a holding handle. A separate handle must be

installed.

The hot and cold supplies must be of equal pressures.

I N S T A L L A T I O N I N S T R U C T I O N S

⁄ Prior to installation, inspect the product for transport damages. After it has been

installed, no transport or surface damage will be honoured.

⁄ The pipes and the fixture must be installed, flushed and tested as per the applicable

standards.

⁄ The plumbing codes applicable in the respective countries must be observed.

⁄ The installation dimensions stated in these installation instructions are ideal for

people of approximately 1800 mm in body height. The dimensions can be altered

if required. In this case, pay attention to the fact that a change of installation height

will also change the minimum height, and that the altered mounting dimensions must

be taken into consideration.

⁄ During installation of the product by qualified trained personnel, make sure that the

entire fastening surface is even and smooth (no protruding seams or tile offset), that

the finish of the wall is suitable to apply the product and has no weak points.

⁄ The mesh washer must be insert to protect the shower against incoming dirt by

pipework. Incoming dirt leads to defects or/and can damage parts of the shower;

such caused faults voids all liability and guarantee claims.

⁄ The product is not designed to be used with steam baths!

⁄ If required, the bottom part of the pipe between the fixture and the shower head

can be shortened with a fine-toothed saw.

⁄ If the continuous water heater causes any problems, or you have different water

pressures you must install a water limiter to the cold supply, (ordered separately,arti-

cle number 97510000).

T E C H N I C A L D A T A

Operating pressure:

Recommended operating pressure:

Test pressure:

Hot water temperature:

Recommended hot water temp.:

Centre distance:

Connections G 1/2:

Thermal disinfection:

F A U L T

⁄ Insufficient water

⁄ Crossflow, hot water being forced into cold water pipe, or

vice versa, when mixer is closed

⁄ Spout temperature does not correspond with temperature

set

⁄ Temperature regulation not possible

⁄ Instantaneous heater didn't work with thermostat

A S S E M B L Y (see page 04)

⁄ Safety against backflow

⁄ The product is exclusively designed for drinking water!

S Y M B O L D E S C R I P T I O N

max. 1 MPa

0,1 - 0,5 MPa

1,6 MPa

(1 MPa = 10 bar = 147 PSI)

max. 70°C

65°C

150±12 mm

cold right - hot left

max. 70°C / 4 min

C A U S E

⁄ Supply pressure inadequate

⁄ Regulator filter dirty

⁄ Shower filter seal dirty

⁄ Backflow preventers dirty or leaking

⁄ Thermostat has not been adjusted

⁄ Hot water temperature too low

⁄ thermo cartridge calcified

⁄ Filters are dirty

⁄ check valve hasn't moved back

⁄ Flow limiter in handshower isn't removed

Do not use silicone containing acetic acid!

S A F E T Y F U N C T I O N (see page 06)

The desired maximum temperature for example max. 42º C can be pre-set

thanks to the safety function.

A D J U S T M E N T (see page 06)

After the installation, the output temperature of the thermostat must be

checked. A correction is necessary if the temperature measured at the output

differs from the temperature set on the thermostat.

M A I N T E N A N C E (see page 07)

⁄ The check valves must be checked regularly according to DIN EN 1717

in accordance with national or regional regulations (at least once a year).

⁄ To guarantee the smooth running of the thermostat, it is necessary from

time to time to turn the thermostat from total hot to total cold.

D I M E N S I O N S (see page 09)

F L O W D I A G R A M (see page 09)

 Overhead shower

 Hand shower

S P A R E P A R T S (see page 10)

S P E C I A L A C C E S S O R I E S (order as an extra)

tile-matching-disk Chrome Plated #95239000 (see page 10)

C L E A N I N G (see page 08)

O P E R A T I O N (see page 11)

To empty the overhead shower after use, hold it in a slightly inclined position.

R E M E D Y

⁄ Check water pressure (If a pump has been installed check

to see if the pump is working).

⁄ Clean filter in front of the mixer and on the MTC-thermo car-

tridge

⁄ Clean filter seal between shower and hose

⁄ Clean backflow preventers, exchange if necessary

⁄ Adjust thermostat

⁄ Increase hot water temperature to 42 ºC to 65 ºC

⁄ Exchange thermo cartridge

⁄ Clean the filter / exchange filter

⁄ Exchange check valves

⁄ Remove flow limiter