Creda 550C 핸드북 - 페이지 4

{카테고리_이름} Creda 550C에 대한 핸드북을 온라인으로 검색하거나 PDF를 다운로드하세요. Creda 550C 4 페이지. Shower

페이지 인쇄

What to do if things go wrong

SELF HELP

If the shower is not working satisfactorily, make the following checks before calling out the contractor.

Any one of these adjustments could restore the performance.

a) The shower cycles

The shower temperature is set too hot causing the thermal cut -out (safety device) to operate.

from HOT to COLD

Turn knob "E" clockwise to increase water flow.

"MEDIUM" setting may need to be selected.

Slowly increase the water temperature by turning knob "E" anti-clockwise until a comfortable

showering temperature has been reached.

You MUST WAIT approx' 20 seconds for each adjustment to affect the water temperature.

b) Water too HOT

Increase water flow by adjusting the temperature control clockwise.

Clean showerhead holes. Select outer or combination spray pattern.

Switch power to "MEDIUM" setting. Increase pressure to water supply e.g. fully open service

valve or stop cock. Check hose is not kinked restricting the water flow.

c) Water too COLD

Decrease water flow by adjusting the temperature control anti-clockwise.

Select inner or outer pattern only. Switch power to "HIGH" setting.

d) Spray pattern poor

Clean showerhead and flush heater. Select outer/inner only.

e) Water goes cold

Check power setting lights are on.

while using

Check water pressure has not fallen so far as to let pressure switch cut out,

shower

e.g. Another tap drawing water off, indicated by "low pressure" light on.

Raise position of handset.

f) Broken parts

Please contact our spares department on 08 44 372 7750. Fitting instructions are provided

PROFESSIONAL SERVICE

If the above checks fail to restore the performance, you should seek professional help.

The person who installed the shower is probably the best one investigate and correct it, and is certainly the person to

contact if you have had a problem in the guarantee period.

The following additional checklist is provided for the benefit of the qualified service person.

WARNING: SWITCH OFF THE ELECTRICITY AT THE ISOLATOR BEFORE REMOVING THE COVER TO MAKE CHECKS

a) Water too HOT

Water flow restricted by blockage in filter of solenoid valve. Switch off water, loosen inlet

connection to solenoid, remove filter in solenoid with long nosed pliers and flush clean.

b) Water too COLD

Check circuit through thermal cut-out.

Check circuit through microswitches on the pressure switch.

Check each element circuit.

Check tightness of electrical connections.

c) Water discharges

Check for cause of high pressure and remove it.

from pressure

Blockage on outlet e.g. blocked showerhead.

relief valve

Replace the pressure relief disc (not covered by guarantee).

d) Water does not flow

Check circuit through solenoid coil. If defective then replace.

when button "A",

Check circuit through microswitches. If defective then replace.

"B"or "C" is

Possible PCB fault. If defective then replace.

pressed.

Power supply not reaching shower.

Creda After Sales Service

We offer a technical advisory service on the telephone to contractors

and other customers with problems in the field.

RING 0844 372 7766

Spare parts can be supplied against Credit or Debit cards.

Remember to quote the exact type of shower, as written on the front face.

The model and serial number are located on the bottom face of the shower.

Make a note of those numbers, and quote them if you call for advice.

Model No: 53-....................... / Serial No:...........................

Note: You may be charged for a service call if you do not have a serial number.

How to maintain your Creda Shower

It is recommend that the shower unit, riser rail, hose et c. be cleaned using

a soft cloth and that the use of abrasive or solvent based cleaning fluid be

avoided, especially on any plated finishes.

We recommend that before any cleaning, the isolating switch be turned off,

thus avoiding accidentally switching on the shower.

The showerhead should be periodically cleaned as detailed on page 3.

YOU MUST REGULARLY INSPECT THE SHOWER HOSE FOR WEAR AND DAMAGE.

REPLACE IF NECESSARY, OR EVERY TWO YEARS, WITH OUR APPROVED PART.

RING 0844 372 7750

Installation Instructions

ALL WIRING AND INSTALLATION MUST BE SUPERVISED BY A QUALIFIED ELECTRICIAN

WARNING: DO NOT INSTALL THIS SHOWER IN A ROOM WHERE IT MAY BE SUBJECT TO FREEZING.

We recommend that the installation is done in the following sequence.

a. Fixing the shower to the wall

b. Plumbing

c. Electrical connections

Fixing the shower to the wall

Position the riser rail at convenient height for majority of users as recommended in diagram 6 and mark its position

Position the heater so that the top of the unit is horizontal and level with,

or up to 0.6 metres (2ft) maximum below the top of the riser rail. Choose a

flat piece of wall to avoid the possibility of distorting the backplate thus making

the front cover a poor fit.

Adjust the position to get the most convenient arrangement taking the following

into account.

•

The possible need to use the handset over the sink for hair washing etc.

•

The heater must not be mounted in the direct spray from the handset.

•

The handset must not be able to come into contact with used water in the

cubicle, bath or basin. If it can, even after the hose has been retained by the

soap dish (see diagram 11), then a vacuum breaker must be fitted. It should

be noted that these devices are liable to minor leakage so they must be

positioned so that any drips are not detrimental.

Fix the riser rail with screws provided. The fixing holes at the base of the

brackets will be disclosed by removing the plastic fronts. Assemble as shown in

diagram 11. Additional "knock-out" slots are available if required to improve

security.

Decide the position of the electrical cable to the unit. If top or bottom entry

is chosen (according to diagram 5), cut away the walls in the backplate as

shown in diagram 7.

Decide the position of entry of the cold water pipe into the unit.

If top, cut away the backplate.

If rear, please read the section on plumbing.

If bottom, remove the front cover (complete with knobs) and cut away the

detachable corner section as shown,

If you have not yet done so, remove the front cover (complete with knobs)

of the unit by undoing the retaining screws at the top and bottom of the

unit and lifting the cover off. Your shower is provided with 2 fixing

positions in the backplate (see diagram 5).

The top-fixing hole is a "key-hole" slot (another key-hole is provided for

alternate fixing), and should be marked and drilled first.

Tighten top screw with head protruding about 10mm from the wall and

hook the backplate over the screw head. This allows for correct and

accurate alignment of your sho wer before marking and fixing the bottom

position.

You may not wish to tighten up both screws at this stage as the holes are

elongated to allow for adjustment after other connections have taken place.