Sharp Aquos LC-13B6U 운영 매뉴얼 - 페이지 15
{카테고리_이름} Sharp Aquos LC-13B6U에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Sharp Aquos LC-13B6U 49 페이지. Sharp lc-13b6u, lc-15b6u liquid crystal television operation manual
페이지 인쇄
EZ SETUP (With AUTO CLOCK Setting)
EZ SETUP during the First Power On
■ When you turn on the TV for the first time, it will automati-
cally memorize the broadcasting channels and clock.
Please perform the following instructions before you press
MAIN POWER.
(1) Insert the batteries into the remote control. (See page 8.)
(2) Connect the antenna cable to the LCD TV set. (See page 9.)
(3) Connect the AC adapter to the POWER INPUT terminal of the LCD
TV set and plug in the AC cord to the wall outlet. (See page 10.)
MAIN POWER
1
Press MAIN POWER, located on the upper side of the
main unit, to turn on the TV. The SELECT LANGUAGE
mode will be displayed.
Press '/" to select "ENGLISH", "ESPAÑOL"
(Spanish) or "FRANÇAIS" (French).
SETUP ... C H – S E T T I N G ]
M E N U
M E N U [
E Z
S E T U P
S E L E C T
L A N G U A G E
E N G L I S H
E S P A Ñ O L
F R A N Ç A I S
2
Press ENTER to access CH-SETTING mode.
Press '/" to select "ON" or "OFF". When you select
"ON", the LCD TV set will automatically memorize the
broadcasting channels.
SETUP ... C H – S E T T I N G ]
M E N U
M E N U [
E Z
S E T U P
C H – S E T T I N G
O N
O F F
A
• If you select "OFF" in "EZ SETUP, CH-SETTING", EZ SETUP will
be canceled.
3
Press ENTER to access AUTO CLOCK mode.
Press '/" to select "ON" or "OFF".
When you select "ON", the LCD TV set will
automatically adjust the clock to search time-signals
(EDS signals), which are provided by some TV stations.
The AUTO CLOCK setting may take from several
minutes to an hour depending on the number of
channels to receive and signal status. If you know the
channel of the EDS signal carrier (PBS or other) in your
area, select "OFF" and follow the procedure in AUTO
CLOCK Setting. (See page 15.)
SETUP ... C H – S E T T I N G ]
M E N U
M E N U [
E Z
S E T U P
A U T O
C L O C K
O N
O F F
14
4
Press ENTER to access START EZ SETUP mode.
Press '/" to select "YES", and press ENTER.
A
• If you want to stop the EZ SETUP process once it has started,
press MENU and it will be canceled. If you want to set up again,
please refer to pages 26 and 27 on CH-SETTING.
SETUP ... C H – S E T T I N G ]
M E N U
M E N U [
E Z
S E T U P
S T A R T
E Z
S E T U P ?
Y E S
N O
C O N N E C T
A N T E N N A
O R
C A B L E .
The tuner will automatically search for the broadcasting
and cable TV channels. (The channel number will
automatically increase when it appears.)
P L E A S E
W A I T
A U T O
P R O G R A M M I N G
The LCD TV set will automatically switch to searching
for EDS signals.
If EDS signals are received, the channel number and time will
be displayed, and then the screen shown in step 5 appears.
P L E A S E
W A I T
N O W
S E A R C H I N G
T I M E
5
Once EZ SETUP is completed, the lowest channel
number memorized will be displayed.
S T E R E O
S A P
M O N O
A
• Do not let the EZ SETUP screen remain unattended for a long time.
• If EZ SETUP does not memorize all the channels in your region,
please refer to pages 26 and 27 for more information on manually
memorizing the channels using CH-SETTING.
• It may be difficult to preset when the broadcasting signals are weak,
the channel cycle frequency is incorrect or the frequency jamming is
occurring around the area. Please refer to pages 26 and 27 for more
information on manually memorizing channels using CH-SETTING.
• If there are no channels with EDS signals or the antenna signal is weak,
the AUTO CLOCK setting may not operate. In this case, a "EDS CH IS
NOT AVAILABLE." message will appear and the mode will change to
MANUAL CLOCK setting. Refer to page 16 to set the clock manually.
2
1 1 : 5 3 A M