Sharp Aquos LC-13B6U 운영 매뉴얼 - 페이지 16
{카테고리_이름} Sharp Aquos LC-13B6U에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Sharp Aquos LC-13B6U 49 페이지. Sharp lc-13b6u, lc-15b6u liquid crystal television operation manual
페이지 인쇄
Setting the CLOCK
AUTO CLOCK Setting
There are two methods of setting the clock: AUTO CLOCK
and MANUAL CLOCK. AUTO CLOCK uses EDS signals,
which are provided by some TV stations, to automatically
adjust the clock. MANUAL CLOCK sets the clock manually in
areas where no channel carries EDS signals.
1
Press MENU to display the Menu screen.
2
Press \/| to select "SETUP".
M E N U [
M E N U [
SETUP]
PICTURE
AUDIO
SETUP
OPTION
C H – S E T T I N G
M T S
C L O C K
A V 2
I N / O U T
V – C H I P
C L O S E D
C O L O R
S Y S T E M
L A N G U A G E
3
Press '/" to select "CLOCK", and press ENTER.
SETUP ... C L O C K ]
M E N U [
M E N U
PICTURE
AUDIO
SETUP
OPTION
C H – S E T T I N G
M T S
C L O C K
A V 2
I N / O U T
V – C H I P
C L O S E D
C O L O R
S Y S T E M
L A N G U A G E
4
Press '/" to select "SET", and press ENTER.
SETUP ... C L O C K ]
M E N U
M E N U [
S E L E C T
S E T
T I M E
D I S P L A Y
A U T O
M A N U A L
5
Press '/" to select "AUTO", and press ENTER.
SETUP ... C L O C K ]
M E N U
M E N U [
S E L E C T
S E T
T I M E
D I S P L A Y
A U T O
M A N U A L
B L O C K
C A P T I O N
B L O C K
C A P T I O N
O P T I O N
O P T I O N
● If you do not know the channel that carries EDS signals in your
area, select "EDS CH" to "AUTO" and press ENTER. If you know
the channel of the EDS signal carrier in your area, press \/| to
select channel and press ENTER. Set the EDS CH and press
ENTER.
SETUP ... C L O C K ]
M E N U
M E N U [
A U T O
C L O C K
S E T
T I M E
D I S P L A Y
E D S
C H
● When set to "AUTO CLOCK", the time is acquired automatically
when MAIN POWER is turned OFF. (This function will not work
when EDS CH is not set.)
S T E R E O
S A P
M O N O
A
• CLOCK:
The AUTO CLOCK setting may take from several minutes to an
hour depending on the number of channels to receive and signal
status.
• EDS CH < AUTO >:
If there are no channels with EDS signals or the antenna signal is
weak, the AUTO CLOCK Setting may not operate. In such a
case, the message "EDS CH IS NOT AVAILABLE." appears, and
the CLOCK setting screen (in step 4 in this page) is displayed.
Refer to MANUAL CLOCK Setting on page 16 to set the clock
manually.
• EDS CH < Not AUTO >:
If the channel you have selected for "EDS CH" is wrong or the
EDS signal carrier is weak, or when there is no broadcast, the
AUTO CLOCK Setting may not operate. In such cases, the
message "EDS CH (XXX) EDS DATA IS NOT AVAILABLE."
appears, and the CLOCK setting screen (in step 4) is displayed as
in the case with EDS CH < AUTO >. Follow step 4 and repeat the
AUTO CLOCK Setting procedure.
• If broadcasting channels are not memorized, EDS signals cannot
be received even when the "EDS CH" is set to "AUTO". In this
case, try EZ SETUP again. (See page 26.)
■ Backup
The clock function is maintained for about 10 minutes even
when the AC adapter has been shut off due to a power
outage or when moving the LCD TV set. (Since about 30
minutes are required to charge the backup power supply, it
may not be possible to maintain the clock function if the
charging time is excessively short.)
If the clock setting has been reset, refer to Setting the
CLOCK on pages 15 and 16.
A U T O
2
1 1 : 5 3 A M
15