Sharp Aquos LC-19D1E 운영 매뉴얼 - 페이지 16
{카테고리_이름} Sharp Aquos LC-19D1E에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Sharp Aquos LC-19D1E 32 페이지. Aquos lcd colour television
페이지 인쇄
Menu operations
G
Sort
Channel positions can be sorted freely.
1
Repeat steps 1 to 4 in Programme Setup.
2
Press a/b to select "Yes", and then press OK.
3
Press a/b/c/d to select the channel you want
to move, and then press OK.
4
Press a/b/c/d to move it to the desired
position, and then press OK.
5
Repeat steps 3 and 4 until all desired channels
are sorted.
G
Erase Programme
An individual programme can be erased.
1
Repeat steps 1 to 4 in Programme Setup.
2
Press a/b to select "Yes", and then press OK.
3
Press a/b/c/d to select the channel you want
to erase, and then press OK.
4
Press OK to erase the selected programme. All
the subsequent programmes move up.
5
Repeat steps 3 and 4 until all desired channels
are erased.
Child Lock
Allows you to use a PIN to protect certain settings from
being accidentally changed.
Changing the PIN
1
Press MENU and the MENU screen displays.
2
Press c/d to select "Setup".
3
Press a/b to select "Child Lock", and then press
OK. If you have already set the PIN under "Child
Lock", enter it here.
Change PIN
Reset
New PIN
Reconfirm
4
Press a/b to select "Change PIN", and enter the
4-digit number as a PIN using 0–9.
5
Enter the same 4-digit number as in step 4 to
confirm.
• When setting the PIN, "Reset" in the Menu will be
selectable and operational.
NOTE
• To view a locked channel (Lock setting in Programme
Setup "Manual Adjust" is set to "On"), you must enter a
PIN. (See page 13 and page 19 for locking channels from
viewing in analogue TV and DTV mode.) When you select
a locked channel, a PIN prompt message pops up. Press
OK to display the PIN input window.
14
Resetting the PIN
Allows you to reset your PIN to the factory preset
"1234".
1
2
3
NOTE
• As a precautionary measure, make a note of your PIN
• See page 25 for resetting the current PIN to the factory
• To relock a channel which has been temporarily
You can assign each input source a label you like.
1
2
3
4
TV only
5
6
NOTE
• You cannot change the label if the input source is TV or
–
–
–
–
–
–
–
–
Menu Operation: C (page 9)
For adjusting a picture's horizontal and vertical
position.
NOTE
• Adjustments are stored separately according to input
• Depending on the input signal type a position setting may
Repeat steps 1 to 3 in Changing the PIN.
Press a/b to select "Reset", and then press OK.
Press a/b to select "Yes", and then press OK.
on the back of this operation manual, cut it out and
keep it in a safe place that children cannot reach.
preset "1234" if you lose or forget your PIN.
unlocked by inputting the correct PIN, turn power off
and then on again.
Input Label
Press b to select the desired input source.
Press MENU and the MENU screen displays.
Press c/d to select "Setup".
Press a/b to select "Input Label", and then press
OK.
Press a/b to select characters and c/d to move
to the desired digit to label the input source.
• When you want to change the input label to the
default name, select "CLEAR" on the "Input Label"
screen.
Repeat step 5 above until the name is fully spelt
out, and then press OK.
• The name can be 6 characters or less.
• When you want to set an input source name of less
than 6 characters, press MENU to exit from the
labelling menu.
DTV.
Position
Item
H-Pos.: Centres the image by moving it to the left or right.
V-Pos.: Centres the image by moving it up or down.
source.
not be available.
TV/DTV/AV only