Sharp Aquos LC-19D1E 운영 매뉴얼 - 페이지 27

{카테고리_이름} Sharp Aquos LC-19D1E에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Sharp Aquos LC-19D1E 32 페이지. Aquos lcd colour television

페이지 인쇄

Appendix

Troubleshooting

Problem

• No power.

• Unit cannot be operated.

• Remote control unit does not

operate.

• Picture is cut off.

• Strange colour, light colour, or

dark, or colour misalignment.

• Power is suddenly turned off.

• No picture.

• No sound.

• The DTV menu screen is

displayed in monochrome and

hard to select the item.

Cautions regarding use in high and low temperature environments

• When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly

delayed. This is not a malfunction, and the unit will recover when the temperature returns to normal.

• Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near

a heater, as this may cause the cabinet to deform and the LCD panel to malfunction.

Storage temperature: –20°C to e60°C.

IMPORTANT NOTE ON RESETTING THE PIN

We suggest that you remove the following instruction from the operation manual to prevent children from

reading it. As this operation manual is multilingual, we also suggest the same with each language. Keep it in

a safe space for future reference.

Repeat steps 1 to 3 in Changing the PIN. (See

page 14.)

Enter "3001" to cancel out the current PIN.

• The PIN resets to the factory preset "1234".

• Check if you pressed B on the remote control unit. (See page 7.)

If the indicator on the TV lights up red, press B.

• Is the AC cord disconnected? (See page 3.)

• Check if you pressed a on the TV. (See page 7.)

• External influences such as lightning, static electricity, etc., may cause improper

operation. In this case, operate the unit after first turning the power off, or

unplugging the AC cord and re-plugging it in after 1 or 2 minutes.

• Are batteries inserted with polarity (e, f) aligned? (See page 4.)

• Are batteries worn out? (Replace with new batteries.)

• Are you using it under strong or fluorescent lighting?

• Is a fluorescent light illuminated to remote control sensor?

• Is the image position correct? (See page 14.)

• Are screen mode adjustments (4:3 Mode/WSS) such as picture size made

correctly? (See pages 15 and 17.)

• Adjust the picture tone. (See pages 10 and 11.)

• Is the room too bright? The picture may look dark in a room that is too bright.

• Check the colour system setting. (See pages 13 and 16.)

• The unit's internal temperature has increased.

Remove any objects blocking vent or clean.

• Check the power control setting. (See page 12.)

• Is sleep timer set? Press SLEEP on the remote control unit until it sets to Off.

• Is connection to other components correct? (See pages 8 and 9.)

• Is input signal type selected correctly after connection? (See page 16.)

• Is the correct input source selected? (See page 8.)

• Is non-compatible signal being input? (See page 27.)

• Is picture adjustment correct? (See pages 10 and 11.)

• Is the antenna connected properly? (See page 3.)

• Is "On" selected in "Audio Only"? (See page 16.)

• Is the volume too low? (See pages 5 and 6.)

• Make sure that headphones are not connected. (See page 6.)

• Check if you pressed e on the remote control unit. (See page 5.)

• Check if "Monochrome" is set to "On". If so, set it to "Off". (See page 11.)

Possible Solution