Sharp Aquos LC-19D1E 운영 매뉴얼 - 페이지 28

{카테고리_이름} Sharp Aquos LC-19D1E에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Sharp Aquos LC-19D1E 32 페이지. Aquos lcd colour television

페이지 인쇄
Sharp Aquos LC-19D1E 운영 매뉴얼
Appendix

RS-232C port specifications

PC Control of the TV
When a program is set, the TV can be controlled from the PC
using the RS-232C terminal. The input signal (PC/video) can
be selected, the volume can be adjusted and various other
adjustments and settings can be made, enabling automatic
programmed playing. Attach an RS-232C cable cross-type
(commercially available) for the connections.
NOTE
• This operation system should be used by a person who is
accustomed to using PCs.
Communication conditions
Set the RS-232C communications settings on the PC to match
the TV's communications conditions. The TV's communications
settings are as follows:
• Baud rate: 9,600 bps
• Data length: 8 bits
• Parity bit: None
Communication procedure
Send the control commands from the PC via the RS-232C
connector.
The TV operates according to the received command and sends
a response message to the PC.
Do not send multiple commands at the same time. Wait until
the PC receives the OK response before sending the next
command.
Command format
Eight ASCII codes e CR
C1 C2 C3 C4 P1 P2 P3
Command 4-digits
Command 4-digits: Command. The text of four characters.
Parameter 4-digits: Parameter 0 – 9, g, blank, ?
Parameter
Input the parameter values, aligning left, and fill with blank(s)
for the remainder. (Be sure that four values are input for the
parameter.)
When the input parameter is not within an adjustable range,
"ERR" returns. (Refer to "Response code format".)
0
–
0
0
0
9
1
When "?" is input for some commands, the present setting value
responds.
?
?
Response code format
Normal response
O
K
Return code (0DH)
Problem response (communication error or incorrect command)
E
R
R
Return code (0DH)
26
RS-232C serial control cable
(cross type, commercially available)
• Stop bit: 1 bit
• Flow control: None
P4
Parameter 4-digits
Return code
3
0
0
0
0
0
?
?
?
Commands
CONTROL ITEM
POWER SETTING
INPUT SELECTION A
CHANNEL
D
C
C
D
D
D
D
INPUT SELECTION B
AV MODE
SELECTION
VOLUME
POSITION
H
H
C
WIDE MODE
W
W
W
W
W
W
W
W
MUTE
M
M
M
AUDIO CHANGE
SLEEP TIMER
O
O
O
O
O
O
TEXT
D
5
5
NOTE
• If an underbar (_) appears in the parameter column, enter a
space.
• If an asterisk * appears, enter a value in the range indicated in
brackets under CONTROL CONTENTS.
COMMAND PARAMETER
CONTROL CONTENTS
P
O
W
R
0
_
_
_
POWER OFF (STANDBY)
I
T
G
D
_
_
_
_
INPUT SWITCHING (Toggle)
I
T
V
D
_
_
_
_
TV (CHANNEL FIXED)
I
D
T
V
_
_
_
_
DTV (CHANNEL FIXED)
I
A
V
D
*
_
_
_
EXT1 – 5 (1 – 5)
C
C
H
*
*
_
_
TV DIRECT CHANNEL (1 – 99)
H
U
P
_
_
_
_
CHANNEL UP
H
D
W
_
_
_
_
CHANNEL DOWN
THREE DIGIT DTV DIRECT CHANNEL
T
V
D
*
*
*
_
(1 – 999) (Non-Nordic countries)
FOUR DIGIT DTV DIRECT CHANNEL
T
V
D
*
*
*
*
(1 – 9999) (Nordic countries only)
T
U
P
_
_
_
_
DTV CHANNEL UP
T
D
W
_
_
_
_
DTV CHANNEL DOWN
I
N
P
1
2
_
_
_
EXT1 (Y/C)
I
N
P
1
3
_
_
_
EXT1 (CVBS)
I
N
P
1
4
_
_
_
EXT1 (RGB)
A
V
M
D
0
_
_
_
AV MODE SELECTION (Toggle)
A
V
M
D
1
_
_
_
STANDARD
A
V
M
D
2
_
_
_
MOVIE
A
V
M
D
3
_
_
_
GAME
A
V
M
D
4
_
_
_
USER
A
V
M
D
5
_
_
_
DYNAMIC (FIXED)
A
V
M
D
6
_
_
_
DYNAMIC
A
V
M
D
7
_
_
_
PC
V
O
L
M
*
*
_
_
VOLUME (0 – 60)
P
O
S
*
*
*
_
H-POSITION AV ( 10 – 10)
P
O
S
*
*
*
_
H-POSITION PC (0 – 180)
V
P
O
S
*
*
*
_
V-POSITION AV ( 20 – 20)
V
P
O
S
*
*
*
_
V-POSITION PC (0 – 120)
L
C
K
*
*
*
_
CLOCK (0 – 180)
P
H
S
E
*
*
*
_
PHASE (0 – 15)
I
D
E
0
_
_
_
WIDE MODE (Toggle)
I
D
E
1
_
_
_
NORMAL (AV/PC)
I
D
E
2
_
_
_
ZOOM 14:9
I
D
E
3
_
_
_
PANORAMA
I
D
E
4
_
_
_
FULL (AV/PC)
I
D
E
5
_
_
_
CINEMA 16:9
I
D
E
6
_
_
_
CINEMA 14:9
I
D
E
8
_
_
_
DOT BY DOT (PC)
U
T
E
0
_
_
_
MUTE (Toggle)
U
T
E
1
_
_
_
MUTE ON
U
T
E
2
_
_
_
MUTE OFF
A
C
H
A
_
_
_
_
SOUND SELECT (ST/Bilingual/mono)
F
T
M
0
_
_
_
OFF
F
T
M
1
_
_
_
30 m
F
T
M
2
_
_
_
1 h 00 m
F
T
M
3
_
_
_
1 h 30 m
F
T
M
4
_
_
_
2 h 00 m
F
T
M
5
_
_
_
2 h 30 m
T
E
X
T
0
_
_
_
TEXT OFF
T
E
X
T
1
_
_
_
TEXT CHANGE (Toggle)
C
P
G
*
*
*
_
DIRECT PAGE JUMP (100 – 899)