DIGISYNTHETIC DS226E(WiFi) 소유자 매뉴얼 - 페이지 5

{카테고리_이름} DIGISYNTHETIC DS226E(WiFi)에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. DIGISYNTHETIC DS226E(WiFi) 10 페이지. Digital loudspeaker management

페이지 인쇄

3.2.3 Input / Output Delay Set

◀

Press MAIN MENU

Rotate the Rotary Encoder to change the parameters with the

step of 0.021ms.

Can also press CURSOR ◀ or ▶ to change the cursor's position

below the value, in order to switch to other step, such as 105ms,

10.5ms, 1.05ms, 0.105ms, 0.021ms, or adjust the Delay switch.

2 IN-A DELAY:

3.2.4 Input / Output PEQ Set

Press MAIN MENU ◀ or ▶ to switch to PEQ settings page.

Press CURSOR ◀ or ▶ to move the cursor position.

Rotate the Rotary Encoder to adjust the parameters at the

cursor position.

The Frequency, Gain of PEQ can be adjusted coarse or fine at the

cursor position.

3 IN-A PEQ 1 ON　PEQ

31.3Hz

3.2.5 Input / Output GEQ Set

Press MAIN MENU ◀ or ▶ to switch to GEQ settings page.

Press CURSOR ◀ or ▶ to move the cursor position.

Rotate the Rotary Encoder to adjust the parameters at the

cursor position.

Gain of GEQ can be adjusted coarse or fine at the cursor position.

5 IN-A GEQ　19 　OFF　

1280 Hz　+6.5dB

3.2.6 Input / Output EQ Bypass Set

Press MAIN MENU ◀ or ▶ to switch to ALL BYPASS settings

page.

Press CURSOR ◀ or ▶ to move the cursor position.

Switch between PEQ ALL-BYPASS and GEQ BYPASS.

Rotate the Rotary Encoder to adjust the parameters at the cursor

position.

4 IN-A　ALL-BYPASS　

PEQ：OFF GEQ：OFF

3.2.7 Input / Output Compressor Set

Press MAIN MENU ◀ or ▶ to switch to COMPRESS settings

page.

Press CURSOR ◀ or ▶ to move the cursor position.

Rotate the Rotary Encoder to adjust the parameters at the cursor

position.

6 IN-A COMPRESS　 OFF

+3.5dBu　

3.2.8 Input / Output LINK Set

Press MAIN MENU ◀ or ▶ to switch to LINK settings page.

Press CURSOR ◀ or ▶ to move the Cursor position.

Rotate the Rotary Encoder to adjust the parameters at the cursor

position.

Press SAVE/ENTER into the link confirmation dialogs.

▶

to switch to DELAY settings page.

933.35mS

321.47m

2241.21ft

+0.0dB

0.500

4:1

AT: 25mS

RT: 200mS

Default is NO, no link setting. Switch between YES and NO with

the Rotary Encoder.

Press SAVE/ENTER again to confirm the link setting.

Note: Yes is chosen as link set, the source channel parameters will

be copied to the target channel.

7 IN-A CHANNEL LINK　

Link to IN-D: OFF

7 IN-A CHANNEL LINK　

Are you sure ? NO

3.2.9 Data COPY of Input / Output Channel

Press MAIN MENU

Rotate the Rotary Encoder to change the target channel.

Press SAVE / ENTER into COPY confirmation dialogs.

Default is NO, no copy operation. Switch between YES and NO

with the Rotary Encoder.

Press SAVE / ENTER again to confirm the copy operation.

Note: At the COPY set, the source channel parameters will be

copied to the target channel.

8 IN-A　CHANNEL COPY　

COPY TO:　IN-B

8 IN-A　Copy data to IN-B　

Are you sure ?　NO

3.2.10 Output HIGH/LOW PASS FILTER Set

Press MAIN MENU

ilter settings page.

◀ or ▶

Press CURSOR

Rotate the Rotary Encoder to adjust the parameters at the cursor

position.

The frequency of

HIGH/LOW - PASS F

coarse or fine at the cursor position.

4 OUT1 HIGH_PASS_FILTER

1620Hz 12 dB Linkriley

3.2.11 Output PHASE Set

Press MAIN MENU

Rotate the Rotary Encoder to change PHASE parameter.

2 OUT1　SET PHASE

Phase: 180 °

3.2.12 SOURCE Set

Press MAIN MENU

® Rotary

Rotate the

Encoder to change SOURCE parameter.

9 OUT1 SET SOURCE

Source: IN-A+IN-B

◀ or ▶

to switch to COPY settings page.

◀ or ▶

to switch to

HIGH/LOW - PASS

to move the cursor.

ilter can be adjusted

◀ or ▶

to switch to PHASE settings page.

◀ or ▶

to switch to SOURCE settings page.