DIGISYNTHETIC DS226E(WiFi) Owner's Manual - Page 5
Browse online or download pdf Owner's Manual for Controller DIGISYNTHETIC DS226E(WiFi). DIGISYNTHETIC DS226E(WiFi) 10 pages. Digital loudspeaker management
Print Page
3.2.3 Input / Output Delay Set
◀
®
Press MAIN MENU
or
®
Rotate the Rotary Encoder to change the parameters with the
step of 0.021ms.
Can also press CURSOR ◀ or ▶ to change the cursor's position
®
below the value, in order to switch to other step, such as 105ms,
10.5ms, 1.05ms, 0.105ms, 0.021ms, or adjust the Delay switch.
2 IN-A DELAY:
3.2.4 Input / Output PEQ Set
Press MAIN MENU ◀ or ▶ to switch to PEQ settings page.
®
Press CURSOR ◀ or ▶ to move the cursor position.
®
®
Rotate the Rotary Encoder to adjust the parameters at the
cursor position.
®
The Frequency, Gain of PEQ can be adjusted coarse or fine at the
cursor position.
3 IN-A PEQ 1 ON PEQ
31.3Hz
3.2.5 Input / Output GEQ Set
Press MAIN MENU ◀ or ▶ to switch to GEQ settings page.
®
Press CURSOR ◀ or ▶ to move the cursor position.
®
®
Rotate the Rotary Encoder to adjust the parameters at the
cursor position.
®
Gain of GEQ can be adjusted coarse or fine at the cursor position.
5 IN-A GEQ 19 OFF
1280 Hz +6.5dB
3.2.6 Input / Output EQ Bypass Set
Press MAIN MENU ◀ or ▶ to switch to ALL BYPASS settings
®
page.
Press CURSOR ◀ or ▶ to move the cursor position.
®
®
Switch between PEQ ALL-BYPASS and GEQ BYPASS.
®
Rotate the Rotary Encoder to adjust the parameters at the cursor
position.
4 IN-A ALL-BYPASS
PEQ：OFF GEQ：OFF
3.2.7 Input / Output Compressor Set
Press MAIN MENU ◀ or ▶ to switch to COMPRESS settings
®
page.
Press CURSOR ◀ or ▶ to move the cursor position.
®
®
Rotate the Rotary Encoder to adjust the parameters at the cursor
position.
6 IN-A COMPRESS OFF
+3.5dBu
3.2.8 Input / Output LINK Set
Press MAIN MENU ◀ or ▶ to switch to LINK settings page.
®
Press CURSOR ◀ or ▶ to move the Cursor position.
®
®
Rotate the Rotary Encoder to adjust the parameters at the cursor
position.
®
Press SAVE/ENTER into the link confirmation dialogs.
▶
to switch to DELAY settings page.
933.35mS
321.47m
ON
2241.21ft
+0.0dB
0.500
4:1
AT: 25mS
RT: 200mS
®
Default is NO, no link setting. Switch between YES and NO with
the Rotary Encoder.
®
Press SAVE/ENTER again to confirm the link setting.
Note: Yes is chosen as link set, the source channel parameters will
be copied to the target channel.
7 IN-A CHANNEL LINK
Link to IN-D: OFF
7 IN-A CHANNEL LINK
Are you sure ? NO
3.2.9 Data COPY of Input / Output Channel
®
Press MAIN MENU
®
Rotate the Rotary Encoder to change the target channel.
®
Press SAVE / ENTER into COPY confirmation dialogs.
®
Default is NO, no copy operation. Switch between YES and NO
with the Rotary Encoder.
®
Press SAVE / ENTER again to confirm the copy operation.
Note: At the COPY set, the source channel parameters will be
copied to the target channel.
8 IN-A CHANNEL COPY
COPY TO: IN-B
8 IN-A Copy data to IN-B
Are you sure ? NO
3.2.10 Output HIGH/LOW PASS FILTER Set
®
Press MAIN MENU
F
ilter settings page.
◀ or ▶
®
Press CURSOR
®
Rotate the Rotary Encoder to adjust the parameters at the cursor
position.
®
The frequency of
HIGH/LOW - PASS F
coarse or fine at the cursor position.
4 OUT1 HIGH_PASS_FILTER
1620Hz 12 dB Linkriley
3.2.11 Output PHASE Set
®
Press MAIN MENU
®
Rotate the Rotary Encoder to change PHASE parameter.
2 OUT1 SET PHASE
Phase: 180 °
3.2.12 SOURCE Set
®
Press MAIN MENU
® Rotary
Rotate the
Encoder to change SOURCE parameter.
9 OUT1 SET SOURCE
Source: IN-A+IN-B
4
◀ or ▶
to switch to COPY settings page.
◀ or ▶
to switch to
HIGH/LOW - PASS
to move the cursor.
ilter can be adjusted
◀ or ▶
to switch to PHASE settings page.
◀ or ▶
to switch to SOURCE settings page.