Crestron CLS-SLVS1 사용자 설명서 - 페이지 4

{카테고리_이름} Crestron CLS-SLVS1에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Crestron CLS-SLVS1 11 페이지. Stand-alone wall box switch

페이지 인쇄

CLW-SW1, SWS1, & SLVS1(W/A/B)

Derating Information for Magnetic Low Voltage and

Neon/Cold Cathode Applications

Part

No Side

Number

Removed

-SW1

1000VA/750W

-SWS1

1000VA/750W

-SLVS1

VA ratings are for input power to the transformer. If you do not

know the input power requirement of the transformer, use the bulb's

wattage rating to determine proper rating.

Derating Information for Fluorescent/HID Applications

Part

No Side

Number

Removed

-SW1

-SWS1

-SLVS1

Derating Information for General Purpose Fans

Part

No Side

Number

Removed

-SW1

-SWS1

-SLVS1

2. To remove a side section, bend the side section

back and forth with a pair of pliers until the

section breaks off from the mounting plate. Use a

file or sandpaper to remove any excess metal.

Prewire for Master Application

Each device has two Class 2 low voltage wires (plus a

ground wire) that provide a Cresnet connection over

shielded twisted-pair to a Crestron control system. These

wires are routed to the bottom of the device for

connection outside of the wallbox. The low voltage wires

are pulled from each device location to the Crestron

control system or a Crestron connection block device. Use

#22 AWG, twisted, shielded, 2-conductor wire. Wiring

can be daisy chained, T-tapped, or home run back to the

control system. Refer to the following wiring diagram.

Wiring Diagram of CLW device to Cresnet

4 • Stand Alone Wall Box Switch: CLW-SW1, SWS1, & SLVS1

One Side

Two Sides

Removed

600VA/450W

400VA/300W

600VA/450W

400VA/300W

No Derating Necessary

One Side

Two Sides

Removed

No Derating Necessary

One Side

Two Sides

Removed

No Derating Necessary

NOTE: The GRAY (Cresnet) wires are not polarized.

These wires can be connected to either the Y or Z line on

a Cresnet port.

NOTE: The BLACK wire (Cresnet ground) should not

be grounded with the GREEN (Ground) wire on the

-SW1/-SWS1.

NOTE: Crestron recommends using Cresnet-DM cable

for connecting the -SW1 and -SWS1 to the Cresnet

network.

Installation

WARNING: Turn off power at the circuit breaker.

Installing with power on can result in serious personal

injury and damage to the device.

NOTE: The -SW1, -SWS1 require a neutral wire for

operation. If no neutral is present, contact a licensed

electrician for installation, otherwise the device will not

work.

NOTE: The -SWS1 must be installed in the same

wallbox that contains the connections to the load.

NOTE: New installations should be checked for short

circuits prior to installing the -SW1, -SWS1, or -SLVS1.

With power off, close the circuit and restore power. If the

load does not work or a breaker trips, check and correct

the wiring or fixture (if necessary). Install the -SW1,

-SWS1, or -SLVS1 only when the short is no longer

present. The warranty is void if the -SW1, -SWS1, or

-SLVS1 is installed and operated with a shorted load.

When installing a -SW1 or a -SWS1 without a slave,

follow the instructions in "Wiring a -SW(S)1 (No

Slaves)" below. If wiring a -SWS1 with a -SLVS1, refer

to "Wiring a -SWS1 with One or More

-SLVS1s" on the next page.

Wiring a -SW(S)1 (No Slaves)

The following describes the installation of a stand-alone

-SW1 or -SWS1.

1. Turn power off at the circuit breaker.

2. Pull Class 2 low voltage wires through a hole in

the drywall located outside of the electrical box,

to the Crestron control system or a Crestron

connection block device. Leave wires outside of

the wallbox for connection to the -SW1 or

-SWS1.

NOTE: Alternate wiring methods may be used

for the Class 2 wiring connection. Refer to

Installation Guide – DOC. 6251A