Crestron FlipTop FT2 Series 빠른 시작 매뉴얼 - 페이지 5

{카테고리_이름} Crestron FlipTop FT2 Series에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Crestron FlipTop FT2 Series 11 페이지. Ac power outlet modules
Crestron FlipTop FT2 Series에 대해서도 마찬가지입니다: 빠른 시작 (2 페이지), 빠른 시작 (2 페이지), 빠른 시작 매뉴얼 (11 페이지), 빠른 시작 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (11 페이지), 빠른 시작 매뉴얼 (9 페이지), 빠른 시작 매뉴얼 (9 페이지), 시작하기 (2 페이지), 시작하기 (2 페이지), 시작하기 (2 페이지), 매뉴얼 (2 페이지), 매뉴얼 (2 페이지), 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (7 페이지), 빠른 시작 매뉴얼 (8 페이지), 빠른 시작 (2 페이지), 빠른 시작 매뉴얼 (2 페이지), 빠른 시작 (2 페이지), 빠른 시작 (2 페이지), 빠른 시작 매뉴얼 (2 페이지), 빠른 시작 (2 페이지), 빠른 시작 (2 페이지)

페이지 인쇄
Crestron FlipTop FT2 Series 빠른 시작 매뉴얼
FT2-700-ELEC-PTL
FlipTop™ FT2 Series Cable Management System, 700 Size, Electrical, Pass-Through Lid

Connect the Network

Automate the one-touch retractors by connecting all retractors in an
FT2 assembly to a control system and a switch, or to a DMPS via a single
Cresnet® cable. Custom programming can trigger the retractors after
five minutes of no video detected.
Connect the FT2 assembly to a Crestron control system or DMPS3 via
the 3-pin connector using standard Cresnet cable. The red power lead is
not connected and should be terminated.
Connect and Place the Power Supply
The FT2-700-ELEC-PTL ships with one 24VDC power supply that is used
to supply power to the power bus in the FT2 assembly. There are six
possible locations to attach the power supply. Connect the power supply
prior to installing any modules.
NOTE:
Two power supplies are required if installing two rapid charging
modules in the FT2-700-ELEC-PTL. For more information, refer to the
FT2A-CHGR-USBA-BASIC Quick Start Guide (Doc. 8423)
FT2A-CHGR-USBA/C Installation Guide
or
(Doc. 8219).
To connect the power supply to the power bus:
1. Underneath the FT2-700-ELEC-PTL, connect the power supply to the
bottom of the power bus.
If connecting one power supply, connect the power supply's power
l
cord to the single connector end of the DC power splitter cable.
Refer to step 1 in
Secure the FlipTop
If connecting two power supplies, connect each power supply's
l
power cord to a barrel jack in the power bus.
2. Use the two included tie wraps to dress the power cord.
3. Slide the power supply into the power supply holder until it is secured
in place.
Quick Start
Assembly.
5