Siemens SIMATIC ET 200SP 장비 매뉴얼 - 페이지 13

{카테고리_이름} Siemens SIMATIC ET 200SP에 대한 장비 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Siemens SIMATIC ET 200SP 44 페이지. Distributed i/o system
Siemens SIMATIC ET 200SP에 대해서도 마찬가지입니다: 매뉴얼 (40 페이지), 사용자 설명서 (21 페이지), 매뉴얼 (34 페이지), 매뉴얼 (48 페이지), 매뉴얼 (30 페이지), 매뉴얼 (34 페이지), 제품 정보 (38 페이지), 매뉴얼 (37 페이지), 매뉴얼 (36 페이지), 매뉴얼 (44 페이지), 매뉴얼 (31 페이지), 매뉴얼 (35 페이지), 매뉴얼 (23 페이지), 구성 매뉴얼 (20 페이지), 매뉴얼 (34 페이지), 매뉴얼 (29 페이지), 매뉴얼 (33 페이지), 매뉴얼 (31 페이지), 사용자 설명서 (32 페이지), 매뉴얼 (31 페이지), 매뉴얼 (28 페이지), 매뉴얼 (41 페이지), 매뉴얼 (32 페이지), 매뉴얼 (49 페이지), 매뉴얼 (24 페이지), 매뉴얼 (34 페이지), 매뉴얼 (41 페이지), 매뉴얼 (30 페이지), 매뉴얼 (31 페이지), 매뉴얼 (27 페이지), 매뉴얼 (24 페이지), 매뉴얼 (24 페이지), 매뉴얼 (25 페이지), 매뉴얼 (49 페이지), 매뉴얼 (40 페이지), 매뉴얼 (38 페이지), 매뉴얼 (39 페이지), 제품 정보 (24 페이지), 매뉴얼 (32 페이지), 제품 정보 (10 페이지), 장비 매뉴얼 (43 페이지), 매뉴얼 (33 페이지), 원본 사용 설명서 (6 페이지), 매뉴얼 (35 페이지), 매뉴얼 (28 페이지), 장비 매뉴얼 (32 페이지), 매뉴얼 (50 페이지), 매뉴얼 (30 페이지), 매뉴얼 (26 페이지), 매뉴얼 (28 페이지), 매뉴얼 (34 페이지), 매뉴얼 (44 페이지), 매뉴얼 (33 페이지), 장비 매뉴얼 (42 페이지), 원본 사용 설명서 (16 페이지)

Siemens SIMATIC ET 200SP 장비 매뉴얼
Properties
The communications module has the following properties:
• Technical properties
– RS232 interface (via BaseUnit)
– RS422/485 interface (via BaseUnit)
– short-circuit proof
– electrically disconnected
– Protocols: 3964(R), Modbus master (RTU), Modbus slave (RTU), Freeport and USS with
The module supports the following functions:
Table 2- 1
Version dependencies of the functions
Function
Firmware update
Identification data I&M0
Parameter reassignment in RUN (using in-
structions)
Diagnostics interrupts
Data transmission rate up to 250 kbit/s
RS485; DMX512 protocol
Option for performance optimization
250 kbit/s with firmware versions <V2.0 can only be configured with instructions or data records
1
Firmware versions V1.0 to V1.0.5 are available for the article number 6ES7137-6AA00-0BA0. Firmware version V2.0 is
available for the article number 6ES7137-6AA01-0BA0.
Accessories
A BaseUnit of type A0 is needed for operation of the communications module. You will find
an overview of the BaseUnits you can use with the communications module in Product
information on the documentation of the ET 200SP distributed I/O system
(http://support.automation.siemens.com/WW/view/en/73021864).
You can find additional information on the accessories in the ET 200SP distributed I/O system
(http://support.automation.siemens.com/WW/view/en/58649293) system manual.
CM PtP communications module (6ES7137-6AA01-0BA0)
Equipment Manual, 03/2021, A5E03790792-01
instructions
Firmware
version of the
module
V1.0 or higher
V1.0 or higher
V1.0 or higher
V1.0 or higher
with
V1.0.5 or higher
1
V2.0 or higher
Configurable as of
STEP 7
(TIA Portal)
PROFINET IO
V12
X
V12
X
V12
X
V12
X
V17
X
V17
X
Product overview
2.1 Properties
GSD
PROFIBUS DP
X
X
X
X
X
13