Siemens SIMATIC ET 200SP 장비 매뉴얼 - 페이지 18

{카테고리_이름} Siemens SIMATIC ET 200SP에 대한 장비 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Siemens SIMATIC ET 200SP 44 페이지. Distributed i/o system
Siemens SIMATIC ET 200SP에 대해서도 마찬가지입니다: 매뉴얼 (40 페이지), 사용자 설명서 (21 페이지), 매뉴얼 (34 페이지), 매뉴얼 (48 페이지), 매뉴얼 (30 페이지), 매뉴얼 (34 페이지), 제품 정보 (38 페이지), 매뉴얼 (37 페이지), 매뉴얼 (36 페이지), 매뉴얼 (44 페이지), 매뉴얼 (31 페이지), 매뉴얼 (35 페이지), 매뉴얼 (23 페이지), 구성 매뉴얼 (20 페이지), 매뉴얼 (34 페이지), 매뉴얼 (29 페이지), 매뉴얼 (33 페이지), 매뉴얼 (31 페이지), 사용자 설명서 (32 페이지), 매뉴얼 (31 페이지), 매뉴얼 (28 페이지), 매뉴얼 (41 페이지), 매뉴얼 (32 페이지), 매뉴얼 (49 페이지), 매뉴얼 (24 페이지), 매뉴얼 (34 페이지), 매뉴얼 (41 페이지), 매뉴얼 (30 페이지), 매뉴얼 (31 페이지), 매뉴얼 (27 페이지), 매뉴얼 (24 페이지), 매뉴얼 (24 페이지), 매뉴얼 (25 페이지), 매뉴얼 (49 페이지), 매뉴얼 (40 페이지), 매뉴얼 (38 페이지), 매뉴얼 (39 페이지), 제품 정보 (24 페이지), 매뉴얼 (32 페이지), 제품 정보 (10 페이지), 장비 매뉴얼 (43 페이지), 매뉴얼 (33 페이지), 원본 사용 설명서 (6 페이지), 매뉴얼 (35 페이지), 매뉴얼 (28 페이지), 장비 매뉴얼 (32 페이지), 매뉴얼 (50 페이지), 매뉴얼 (30 페이지), 매뉴얼 (26 페이지), 매뉴얼 (28 페이지), 매뉴얼 (34 페이지), 매뉴얼 (44 페이지), 매뉴얼 (33 페이지), 장비 매뉴얼 (42 페이지), 원본 사용 설명서 (16 페이지)

Siemens SIMATIC ET 200SP 장비 매뉴얼
Product overview
2.3 Properties of the interfaces
2.3.2

Properties of the RS422/485 interface

Definition
The RS422/485 (X27) interface is a differential voltage interface for serial data transmission.
Properties
The RS422/485 (X27) interface has the following properties and meets the following
requirements:
Type
BaseUnit terminals
RS422 signals
RS485 signals
Max. data transmission
rate
Max. cable length
Standard
18
Differential voltage interface
Terminals connected to the electronics module (see RS422/485 interface of
the communications module (Page 23) for assignment)
T (A), R (A), T (B), R (B), GND;
all signals are isolated against the backplane bus and the load voltage
R/T (A), R/T (B), GND;
all signals isolated against backplane bus and load voltage
250 kbps
1200 m for 0.3...19.2 kbps,
500 m for 38.4 kbps,
350 m for 76.8 kbps,
250 m for 115.2 kbps,
200 m for 250 kbps;
cable type LIYCY 3 x 2 x 0.14. T(A)/T(B) and R(A)/R(B) twisted in pairs
To ensure interference-free operation for cable lengths > 50 m, you must
install a terminating resistor of approx. 330 Ω at the receiver end.
DIN 66259 Parts 1 and 3, EIA-RS422/485, CCITT V.11
CM PtP communications module (6ES7137-6AA01-0BA0)
Equipment Manual, 03/2021, A5E03790792-01