Epson 1815p - PowerLite XGA LCD Projector 사용자 설명서 - 페이지 12

{카테고리_이름} Epson 1815p - PowerLite XGA LCD Projector에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson 1815p - PowerLite XGA LCD Projector 27 페이지. Release of check tool for network projectors v1.00 for windows
Epson 1815p - PowerLite XGA LCD Projector에 대해서도 마찬가지입니다: 사용자 설명서 (42 페이지), 운영 매뉴얼 (36 페이지), 운영 매뉴얼 (47 페이지), 빠른 설정 (2 페이지), 사용자 설명서 (1 페이지), 기능 설명서 (5 페이지), 소프트웨어 설명서 (2 페이지), 적합성 선언 (4 페이지), 부품 목록 (1 페이지), 제품 지원 게시판 (45 페이지), 제품 지원 게시판 (25 페이지), 제품 지원 게시판 (22 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (41 페이지), 제품 지원 게시판 (34 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (15 페이지), 제품 지원 게시판 (22 페이지)

페이지 인쇄
Epson 1815p - PowerLite XGA LCD Projector 사용자 설명서
PowerLite 1810p/1815p
Configuring the Network Settings for Windows
Before connecting to the projector, you need to make sure the
settings for your notebook's or PC's network card match the
settings you entered for the projector.
1. Access your wireless network Properties window. For
example, in Windows XP you would click
Panel > Network and Internet Connections
the
Network Connections
this:
Right-click and select Properties
2. Right-click the
Wireless Network Connection
select
. You see a screen similar to this:
Properties
3. Click the
button.
Configure
12
PowerLite 1810p/1815p
-
Start > Control
. Then click
icon. You see a screen similar to
icon and
Click here
4. Click the
Advanced
5. Check your wireless card or adapter device settings.
(Depending on the type of card or adapter you're using,
some of the settings may be different from those listed here.)
❏ Set the Network Type to
❏ Set the SSID to match the name you assigned to the
projector's ESSID.
❏ Make sure Encryption is
6. Click the
General
or adapter is enabled.
7. When you're done, click
box.
Now you're ready to connect to the projector. See "Projecting
Over a Network" on page 17.
Note: When you connect in Ad Hoc mode, your connection to other
wireless networks or devices is broken. If you need to remain
connected to your wireless network, use Access Point mode. Also,
make sure you reconnect to your original wireless network when you
are done using the projector.
Configuring the Network Settings for Macintosh
Your AirPort software is automatically configured to allow your
Mac to detect both computer-to-computer (Ad Hoc) and
Access Point networks. Typically, you only need to select your
projector's ESSID from the AirPort status menu on the Mac
menu bar. If you're having problems detecting the projector,
follow these steps:
1. From the Apple pull-down menu, select
.
Preferences
2. Double-click the
Network
settings window.
3/08
tab. You see a screen similar to this:
.
802.11 Ad Hoc
.
Disabled
tab and make sure that your wireless card
to close the Properties dialog
OK
System
icon. You see the Network