Cisco 6945 Series 관리 매뉴얼 - 페이지 12

{카테고리_이름} Cisco 6945 Series에 대한 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco 6945 Series 14 페이지. 6900 series
Cisco 6945 Series에 대해서도 마찬가지입니다: 데이터시트 (5 페이지), 빠른 참조 (2 페이지), 릴리스 정보 (18 페이지), 사용자 설명서 (10 페이지), 사용자 설명서 (38 페이지), 사용자 설명서 (8 페이지), 설정 매뉴얼 (16 페이지), 특징 (29 페이지), 빠른 시작 매뉴얼 (2 페이지), 빠른 설치 및 사용자 설명서 (12 페이지), 빠른 참조 사용 설명서 (2 페이지), 매뉴얼 (2 페이지), 지침 (3 페이지), 빠른 시작 매뉴얼 (2 페이지), 기능 설명서 (4 페이지), 사용자 설명서 (34 페이지), 빠른 설치 매뉴얼 (12 페이지), 빠른 참조 매뉴얼 (2 페이지)

페이지 인쇄
Cisco 6945 Series 관리 매뉴얼
Using Cisco Unified IP Phones with Different Protocols
Procedure
Take one of these actions:
Step 1
•
•
•
If you are not using DHCP in your network, configure the network parameters for the phone.
Step 2
See
Save the configuration updates, click Apply Config, click OK when the Apply Configuration
Step 3
Information dialog displays, then have the user power cycle the phone.
Converting an In-Use Phone from One Protocol to the Other Protocol
If Cisco Unified IP phones presently connected to Cisco Unified CM are using the SCCP protocol to
receive and place calls and you now want some or all of these phones to use the SIP protocol, the phone
firmware for each phone type must be upgraded from SCCP to the recommended SIP version before the
phones can register. If Cisco Unified IP phones to be connected to Cisco Unified CM are brand new,
out-of-the-box, the SCCP phone firmware preloaded at the factory must be upgraded to the
recommended SIP version before your SIP phones can complete registration.
For information about how to convert an in-use phone from one protocol to the other, see the Cisco
Unified Communications Manager Administration Guide, Cisco Unified IP Phone Configuration,
section Migration Existing Phone Configuration to a Different Phone.

Deploying a Phone in an SCCP and SIP Environment

To deploy Cisco Unified IP Phones in an environment that includes SCCP and SIP and in which the
Cisco Unified Communications Manager Auto-Registration parameter is SCCP, perform these general
steps:
Procedure
Set the Cisco Unified Communications Manager auto_registration_protocol parameter to SCCP.
Step 1
From Cisco Unified Communications Manager Administration, choose System > Enterprise
Parameters.
Install the phones.
Step 2
Change the Auto Registration Protocol enterprise parameter to SIP.
Step 3
Auto-register the SIP phones.
Step 4
Cisco Unified IP Phone 6921, 6941, 6945, and 6961 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)
2-12
To auto-register the phone, set the Auto Registration Phone Protocol parameter in Cisco Unified
Communications Manager Administration to SIP.
To provision the phone using the Bulk Administration Tool (BAT), choose the appropriate phone
model and choose SIP from the BAT.
To provision the phone manually, make the appropriate changes for SIP on the Phone Configuration
window in Cisco Unified Communications Manager Administration.
Refer to Cisco Unified Communications Manager Administration Guide for detailed information
about Cisco Unified Communications Manager configuration.
Refer to Cisco Unified Communications Manager Bulk Administration Guide for detailed
information about using the BAT.
Configuring Startup Network Settings, page
3-15.
Chapter
OL-24567-01