Epson 7850p - PowerLite XGA LCD Projector 제품 정보 매뉴얼 - 페이지 12

{카테고리_이름} Epson 7850p - PowerLite XGA LCD Projector에 대한 제품 정보 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson 7850p - PowerLite XGA LCD Projector 25 페이지. Release of check tool for network projectors v1.00 for windows
Epson 7850p - PowerLite XGA LCD Projector에 대해서도 마찬가지입니다: 사용자 설명서 (42 페이지), 운영 매뉴얼 (36 페이지), 사용자 설명서 (12 페이지), 교체 부품 (1 페이지), 운영 매뉴얼 (47 페이지), 제품 지원 게시판 (30 페이지), 설치 매뉴얼 (5 페이지), 빠른 설정 (2 페이지), 브로셔 및 사양 (2 페이지), 기술 요약 (7 페이지), 제품 지원 게시판 (25 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (12 페이지), 제품 지원 게시판 (42 페이지), 제품 지원 게시판 (22 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (41 페이지), 제품 지원 게시판 (34 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (15 페이지), 제품 지원 게시판 (22 페이지)

Epson 7850p - PowerLite XGA LCD Projector 제품 정보 매뉴얼
Setting the Remote Control ID
The remote control's default ID is zero, which allows it to
control any projector (although not switch between
projectors). If you want to switch between projectors, follow
these steps to change the remote control's ID to match that of
the projector:
1. Press the
button on the remote
ID
control. You see it light up.
2. Press one of the numbered
buttons on the remote
control to select the desired
ID (0 through 9). Select zero
to control all projectors, or
select a number to match the
ID of the projector(s) you
want to operate.
The
button's light shuts off and the new ID is registered.
ID
If you would like to check the remote control's current ID,
press the
button twice in succession. Count the number of
ID
flashes; this number corresponds to the remote control's ID. If
it doesn't flash, the ID is set to zero.

Presenting Over a Wireless Network

Using EMP NS Connection, you can project images shown
on your computer screen directly to your audience without
connecting the projector to your computer. Before you begin,
make sure you've installed EMP NS Connection from the
CD-ROM that came with your projector. See the User's Guide
for installation instructions.
Note: Your computer must be running Microsoft
2000, Me or 98. EMP NS Connection does not support
Macitnosh.
Starting EasyMP
Before you can connect to the projector wirelessly, you have to
switch it to EasyMP mode.
1. Turn on the remote control and the projector. Press the
button on the remote control to select EasyMP as
EasyMP
the source.
2. Locate the EPSON 802.11b card that came with your
projector. Insert it with the blue label facing outward.
Zero
®
Windows XP,
If you've already configured the projector for your wireless
network, go to "Projecting Wirelessly" on page 15. Otherwise,
continue with the next section.
6/03
EPSON PowerLite 7850p Projector
Note: Only the EPSON 802.11b card is guaranteed to work.
Other cards may not be compatible.
Depending on whether your projector is set up to
connect in Ad Hoc mode or Access Point mode (also called
infrastructure mode), you see one of these screens:
EPSON PowerLite 7850p Projector
Ad Hoc mode
Access Point
mode
11
-