Siemens CM736G1.1B 사용자 설명서 및 설치 지침 - 페이지 13
{카테고리_이름} Siemens CM736G1.1B에 대한 사용자 설명서 및 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Siemens CM736G1.1B 44 페이지.
페이지 인쇄Press
to switch the appliance on.
3.
Apply the following settings:
4.
Type of heating
Temperature
Cooking time
→ "Basic operation", Page 13
Start the operation.
5.
8 Basic operation
8.1 Switching on the appliance
Press
to switch the appliance on.
▶
a The display shows the menu.
8.2 Switching off the appliance
Switch your appliance off when you are not using it.
The appliance automatically switches itself off if it is not
used for a certain period of time.
Press
to switch the appliance off.
▶
a The appliance switches off. Any functions currently
in progress are cancelled.
a The time or residual heat indicator appears on the
display.
8.3 Starting the operation
You must start each operation.
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures above
120 °C, this will damage the enamel.
Do not use the appliance if there is water on the
▶
cooking compartment floor.
Wipe away any water on the cooking compartment
▶
floor before operation.
Use
to start the operation.
▶
a The settings appear on the display.
8.4 Interrupting the operation
You can interrupt the operation and then continue
again.
1.
To interrupt the operation, press
Press
again to resume operation.
2.
8.5 Setting an operating mode
After you have switched on the appliance, the menu
appears on the display.
To scroll through the various selection options,
1.
swipe to the left or right on the display.
To select a function, press the corresponding tile.
2.
a Depending on the function, possible adjustment val-
ues or other tiles are available for selection.
3.
If required, press on another tile.
To change the adjustment values:
4.
4D hot air
Maximum
1 hour
.
Ventilate the kitchen while the appliance is heat-
‒
ing.
a Once the cooking time has elapsed, a signal tone
sounds. A note appears on the display confirming
that the operation has finished.
Press
to switch the appliance off.
6.
Once the appliance has cooled down, clean the
7.
smooth surfaces in the cooking compartment with a
detergent solution and a dish cloth.
Clean the accessories thoroughly using a detergent
8.
solution and a dish cloth or soft brush.
Swipe over the blue adjustment line or push the
‒
adjustment line to the appropriate point.
Or press
and enter the value directly via the
‒
number field that appears.
5.
Use
to start the operation.
If the operation is ended:
6.
If required, you can select other settings and re-
‒
start the operation.
When the food is ready, use
‒
pliance off.
Tip: You can save your settings as "Favourites"
use these again.
→ "Favourites", Page 20
8.6 Setting the type of heating and the
temperature
Press "Types of heating".
1.
Press the type of heating that you want to use.
2.
Set the temperature using
3.
ment bar. Or enter the temperature directly via the
number field
.
If required, you can implement additional settings:
– → "Rapid heating", Page 14
– → "Time-setting options", Page 14
– → "Microwave", Page 16
– → "Ventilation function Crisp Finish", Page 18
Use
to start the operation.
4.
a The appliance starts heating.
a The adjustment values and how long the appliance
has already been in operation are shown on the dis-
play.
When the food is ready, use
5.
ance off.
Note: The most suitable type of heating for your food
can be found in the type of heating description.
Changing the type of heating
When you change the type of heating, the other set-
tings are also reset.
Press
.
1.
Press
.
2.
Press the type of heating that you want to use.
3.
Reset the operation and use
4.
Changing the temperature
Once the operation has started, you can change the
temperature at any time.
Press the temperature.
1.
Basic operation en
to switch the ap-
and
or
or via the adjust-
to switch the appli-
to start.
13