Siemens CM736G1.1B 사용자 설명서 및 설치 지침 - 페이지 15
{카테고리_이름} Siemens CM736G1.1B에 대한 사용자 설명서 및 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Siemens CM736G1.1B 44 페이지.
페이지 인쇄Time-setting
Use
option
End time
Along with the cooking time, you can
set the time at which you want the
operation to end. The appliance
starts up automatically so that the
operation finishes at the required
time.
Timer
You can set the timer to run inde-
pendently of the appliance during op-
eration. It does not affect the appli-
ance.
10.1 Setting the cooking time
You can set the cooking time for the operation of up to
24 hours.
Requirement: An operating mode and temperature or
setting have been set.
Press "Cooking time".
1.
To set the cooking time, press the relevant time
2.
value, e.g. hour display "h" or minute display "min."
a The selected value is marked in blue.
Set the cooking time using
3.
ment bar. Or enter the cooking time directly via the
number field
.
If required, use
to reset the adjustment value.
Press "Apply".
4.
Use
to start the operation.
5.
a The appliance starts to heat and the time counts
down.
a Once the cooking time has elapsed, a signal tone
sounds. A note appears on the display confirming
that the operation has finished.
Once the cooking time has elapsed:
6.
If required, you can select other settings and re-
‒
start the operation.
When the food is ready, use
‒
pliance off.
Changing the cooking time
You can change the cooking time at any time.
Press the cooking time.
1.
Change the cooking time using
2.
adjustment bar. Or enter the temperature directly via
the number field
.
Press "Apply".
3.
Cancelling the cooking time
You can cancel the cooking time at any time.
Press the cooking time.
1.
Reset the cooking time using
2.
Note: For operating modes that always require a
cooking time, the appliance resets the cooking time
to the preset value.
Press "Apply".
3.
or
or via the adjust-
to switch the ap-
or
, or via the
.
10.2 Setting the end time
You can delay the time at which the cooking time for
the operation is due to end by up to 24 hours.
Requirements
¡ An operating mode and temperature or level have
been set.
¡ A cooking time is set.
Press "End time".
1.
Use
or
to delay the time or enter the time dir-
2.
ectly via the number field
If required, use
to reset the setting value.
Press "Apply".
3.
Press
to start the operation.
4.
a The display shows the start time. The appliance is in
standby mode.
a Once the start time has been reached, the appli-
ance starts heating and the cooking time starts
counting down.
a When the time has elapsed, a signal sounds. A
message appears on the display confirming that the
operation has finished.
Once the cooking time has elapsed:
5.
If required, you can select other settings and re-
‒
start the operation.
When the food is ready, use
‒
pliance off.
Setting the end time
To achieve good cooking results, only change the set
time before the operation starts and before the cooking
time starts counting down.
Press "End time".
1.
Use
or
to change the time or enter the time dir-
2.
ectly via the number field
Press "Apply".
3.
Cancelling the end time
You can delete the set time at any time.
Press "End time".
1.
Use
to reset the time.
2.
Note: For operating modes that always require a
cooking time, the appliance resets the time at which
the cooking time ends to the next possible time.
3.
Press "Apply".
10.3 Setting the timer
The timer runs independently during the operation. You
can set the timer when the appliance is switched on or
off, up to 24 hours. The timer has its own signal tone
so that you can tell whether it is the timer or a cooking
time that has elapsed.
Press the
button.
1.
To set the timer, press the relevant time value on
2.
the display, e.g. hour display "h" or minute display
"min".
a The selected value is marked in blue.
Set the timer using
3.
bar. Or enter the timer time directly via the number
field
.
If required, use
to reset the adjustment value.
To start the timer, press "Start".
4.
a The timer counts down.
Time-setting options en
.
to switch the ap-
.
or
, or via the adjustment
15