Siemens HB24D582 Series 사용 설명서 - 페이지 15
{카테고리_이름} Siemens HB24D582 Series에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Siemens HB24D582 Series 24 페이지.
페이지 인쇄
Troubleshooting
Malfunctions often have simple explanations. Please read the
following instructions before calling the after-sales service.
Repairs may only be carried out by fully trained after-sales
service technicians. Incorrect repairs to your appliance may
present considerable risks for the user.
Problem
The appliance does not work
Appliance does not start.
appears in the display.
The appliance cannot be started
The appliance is not in operation. A dura-
tion is shown in the display
and
:
light up in the display
0
‹
‹‹
The
indicator appears even though the
¯
water tank is full
The
indicator appears even though the
¯
water tank is not yet empty, or the water
tank is empty but the
indicator does not
¯
appear
The water tank empties for no discernible
reason. The evaporator dish is overflowing
The evaporator dish has boiled dry even
though the water tank is full
The
indicator appears
¯
There is a "pop" noise during cooking
When you cook with steam, a lot of steam
is created
When cooking with steam, a lot of steam is
created again
Steam escapes from the ventilation slots
during cooking
The appliance is not producing steam
properly
Error message
appears in the dis-
"‹‚‚
play
Possible cause
The plug is not plugged into the mains.
Power cut
Fuse defective
Faulty operation
Descaling has been cancelled
:
min
Nx ‹
...‹
The appliance door is not fully closed
A control knob was unintentionally
pressed
The
†
button was not pressed after mak-
ing the setting
Power cut
The water tank has not been pushed in
properly
The detection system is not working
The water tank is dirty. The mobile water
level indicators are jammed
The water tank was not closed properly
The tank cover seal is dirty
The seal in the tank cover is defective
The water tank has not been pushed in
properly
The feed line is blocked
The appliance has not been used for at
least 2 days and the water tank is full
Cold/warm effect with frozen food, caused
by the steam
The appliance is being automatically cali-
brated
The appliance is unable to calibrate itself
automatically if cooking times are too
short
Limescale has formed in the appliance
A button was pressed for too long or is
jammed
:
Risk of electric shock!
Work on the appliance electronics may only be performed by
■
a specialist.
Always disconnect the appliance from the power supply
■
when work is carried out on the electronics. Switch off the
circuit breaker or remove the fuse from your household fuse
box.
Notes/remedy
Connect the appliance to the electricity
supply
Check whether other kitchen appliances
are working
Check in the fuse box to make sure that
the fuse for the appliance is OK
Switch the appliance off using the fuse in
the fuse box. Wait approximately
10 seconds and then switch it back on
Turn the operating mode selector to
and rinse the appliance twice
(see section: Cancelling descaling)
Close the appliance door.
Press and hold the
Press the
cooking operation, or press and hold the
button to cancel the setting
†
Reset the clock time (see section: "Time-
setting options")
Slide in the water tank until it engages
Call the after-sales service
Shake and clean the water tank. If the
parts cannot be released, obtain a new
water tank from the after-sales service.
Close the lid until you feel it engage.
Clean the seal
Obtain a new water tank from the after-
sales service
Slide in the water tank until it engages
Descale the appliance. Check whether the
water hardness is set correctly
Empty and clean the water tank. Always
empty the water tank after cooking
This is normal.
This is normal.
Reset the appliance to the factory settings
(see Basic settings section). Then start
steaming at 100 °C for 20 minutes
This is normal.
Start descaling (see Section: Descaling)
Press the
sage. Press each button and check that it
is clean
button
†
†
button briefly to start the
button to clear the fault mes-
0
È
15