Cisco 7942 사용자 설명서 - 페이지 5

{카테고리_이름} Cisco 7942에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco 7942 6 페이지. Etherworks
Cisco 7942에 대해서도 마찬가지입니다: 사용자 설명서 (6 페이지), 사용자 설명서 (4 페이지), 사용자 설명서 (6 페이지), 사용자 설명서 (4 페이지), 사용자 설명서 (13 페이지), 사용자 설명서 (13 페이지), 빠른 참조 매뉴얼 (3 페이지), 사용자 교육 매뉴얼 (7 페이지), 빠른 참조 매뉴얼 (8 페이지), 빠른 참조 매뉴얼 (9 페이지), 사용자 설명서 (2 페이지), 사용자 교육 매뉴얼 (2 페이지), 사용자 설명서 (4 페이지), 빠른 참조 (4 페이지), 빠른 참조 매뉴얼 (6 페이지), 빠른 참조 매뉴얼 (3 페이지), 매뉴얼 (2 페이지), 빠른 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (2 페이지), 문제 해결 및 유지 관리 (27 페이지), 사용자 설명서 (2 페이지)

Transfer a Call

Transfer a selected call to another number in one of two ways:

•

Blind transfer—Immediately redirects the call without allowing you to speak to the transfer recipient.

•

Consult transfer—Redirects the call after first allowing you to announce the call to the transfer

recipient.

To transfer a call, perform the following steps:

1. During a call, press the Trnsfer soft key. The call is placed on hold.

2. Dial the number to which you want to transfer the call.

3. To make a blind transfer, press the Trnsfer soft key again.

To make a consult transfer, wait for an answer. Announce the call. Then press the Trnsfer button.

To cancel your consult call-transfer attempt press the EndCall soft key, then press the Hold button.

Note If a call rings in when you want to transfer a call and the Trnsfer soft key is not displayed, use the

Navigation button to place the focus back on the call you want to transfer. Then the Trnsfer soft key will

be available to use.

Forward All Calls

To forward all incoming calls to another number, use the following method:

1. Press the CFwdALL soft key. You will hear a confirmation beep.

2. Dial the number to which you want to forward all your calls. Dial the number exactly as you would if

you were placing a call to that number. Remember to include any locally required prefix numbers (ie:9.)

The phone display is updated to show that calls are to be forwarded.

To cancel call forwarding, press the CFwdALL soft key.

Note To forward your calls to voice mail, enter the voice-mail extension 63500.

Place a Conference Call

To initiate a conference call, perform the following steps:

1. During a call, press the more > Confrn soft keys to put the call on hold and open a new line.

2. Place a call to another number.

3. When the call connects, press the Confrn soft key again to add the new party to the existing

call.

To add a third party repeat steps 1 through 3. You cannot add more than three parties to a conference call.

Page 5 of 6

5/5/2009