Cisco 8841 사용자 설명서 - 페이지 27

{카테고리_이름} Cisco 8841에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco 8841 29 페이지. Mpp phones
Cisco 8841에 대해서도 마찬가지입니다: 릴리스 정보 (24 페이지), 사용자 설명서 (16 페이지), 빠른 참조 매뉴얼 (7 페이지), 특징 (16 페이지), 빠른 시작 매뉴얼 (2 페이지), 사용자 설명서 (2 페이지), 빠른 참조 매뉴얼 (2 페이지), 빠른 참조 매뉴얼 (2 페이지), 빠른 매뉴얼 (2 페이지), 빠른 참조 매뉴얼 (6 페이지), 사용자 설명서 (24 페이지), 사용자 설명서 (28 페이지), 펌웨어 마이그레이션 마스터 매뉴얼 (31 페이지), 사용자 설명서 (30 페이지), 매뉴얼 (44 페이지), 빠른 시작 매뉴얼 (2 페이지), 짧은 설명서 (2 페이지), 빠른 시작 매뉴얼 (2 페이지), 재구성 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (6 페이지), 매뉴얼 (22 페이지), 시작하기 (2 페이지), 빠른 시작 매뉴얼 (2 페이지), 매뉴얼 (48 페이지), 사용자 설명서 (40 페이지), 빠른 시작 (2 페이지)

Troubleshooting guide

We'll always aim to give you the best service possible. However, no system can be guaranteed to

run error-free all the time. Here are a few issues that may arise - and how you can solve them.

The handset shows an on-screen extension, but is also showing an amber light

on the line key.

This means it's successfully downloaded its configuration but hasn't been registered on Horizon.

It's normally a local fault, where our IP traffic is being restricted in reaching our Session Boarder

Controller. In a case like this, please check the following before raising a fault:

•

Ensure all router port settings - as defined earlier in this document - have been implemented.

Check the setting especially on port 5060 and make sure that SIP ALG is disabled.

Eliminate LAN variables, ideally by plugging the handset directly into the router. If your router

•

does not provide power over Ethernet, make sure the only thing between the router and the

handset is the Power Over Ethernet switch and that all the wires and units are working

correctly.

•

Make sure the handset is still assigned to a user on the Horizon Portal.

Plug the handset into a different port that you know definitely works.

•

If none of these solve the issue, call our support team - contact details are in the following section.

The handset boots up, but displays an amber light on the line keys and no on-

screen extension

This means it's either been provisioned incorrectly, or it can't gain a connection to the public internet.

Try the following checks:

Ensure all router port settings - as defined earlier in this document - have been implemented.

•

Check the setting especially on port 5060 and make sure that SIP ALG is disabled.

Check you've assigned a local IP address, by looking it up on the routers ARP cache or

•

similar.

•

Eliminate LAN variables, ideally by plugging the handset directly into the router. If your router

does not provide power over Ethernet, make sure the only thing between the router and the

handset is the Power Over Ethernet switch and that all the wires and units are working

correctly.

Make sure the handset is still assigned to a user on the Horizon Portal.

•

Plug the handset into a different port that you know definitely works.

If you think the handset hasn't been configured properly, call our support team for more help.

The handset displays an "Initialising Network" message constantly

This means the handset can't connect to the local network. Before raising a fault, try the following:

Horizon

Cisco IP Phone 8841/8851 and 8861 User Guide

Page