Epson 7880 - Stylus Pro Color Inkjet Printer 매뉴얼 - 페이지 9

{카테고리_이름} Epson 7880 - Stylus Pro Color Inkjet Printer에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson 7880 - Stylus Pro Color Inkjet Printer 12 페이지. Warranty statement
Epson 7880 - Stylus Pro Color Inkjet Printer에 대해서도 마찬가지입니다: 빠른 시작 설치 매뉴얼 (1 페이지), 네트워크 매뉴얼 (46 페이지), 제한 보증 (12 페이지)

페이지 인쇄

Epson 7880 - Stylus Pro Color Inkjet Printer 매뉴얼

Follow these steps to align the print head using the control

panel:

1. Make sure the printer is turned on. Then load Epson

Enhanced Matte Paper.

Tip:

To properly align the print head, you can also use Epson

Doubleweight Matte Paper or Ultra Premium Photo Paper Luster.

2. Press the

button.

3. Press d until

HEAD ALIGNMENT

press

Menu. PAPER THICKNESS

4. Press

. The

STANDARD

This is the correct thickness setting for most Epson papers.

5. Press

to save the setting.

6. Press l, then press d to highlight

7. Press the

button to highlight

again.

(uni-directional) is highlighted. This is

UNI-D

the type of alignment to start with.

8. Press

to start the alignment process.

Each head alignment takes about 7 minutes. The printer's

white beam sensor reads the alignment pattern and adjusts

the printer automatically. Make sure you don't open the

front cover or turn off the printer during this process.

9. When the uni-directional alignment is finished, press the d

button until

BI-D 2-COLOR

to start the bi-directional black alignment process.

10. When the bi-directional black alignment is finished, press d

until

is highlighted. Then press

BI-D ALL

alignment process.

11. When done, press the

alignment mode.

If you want to fine-tune the automatic alignment process, you

can perform a manual head alignment. See your electronic

User's Guide for instructions.

Replacing the Paper Cutter Blade

If you notice that your paper isn't cut cleanly, the cutter blade

may need to be replaced. If you use the blade to cut heavy

stock, you will damage the blade and need to replace it. For a

list of media that are not recommended for use with the

cutter, see the User's Guide or Printer Guide.

You can check the status of your cutter by printing a status

sheet. See page 6 for instructions. You can obtain a new cutter

blade from Epson (part number C12C815291).

9 - Epson Stylus Pro 7880/9880

is highlighted, then

is highlighted.

setting is selected by default.

ALIGNMENT

, then press

AUTO

is highlighted. Then press

to start the

Pause button to exit head

Removing the Old Blade

Make sure the printer is turned on, then follow these steps to

remove the blade:

1. Press the

button.

2. Press d until

MAINTENANCE

CUTTER REPLACEMENT

again.

4. Press

. The print head moves to the replacement

position.

OPEN FRONT COVER TO SEE CUTTER

REPLACEMENT LABEL

5. Open the front cover.

6. When

SEE LABEL TO REPLACE CUTTER

the LCD display, hold down the side pin (as shown to the

left) and turn the latch to the right (as shown on the right).

7. Release the side pin. The cutter pops out.

Warning

The blade is sharp. Be careful when removing it.

10/07

Epson Stylus Pro 7880/9880

is highlighted, then press

is highlighted. Press

is displayed.

is displayed on