Epson 7880 - Stylus Pro Color Inkjet Printer Manuel - Sayfa 9
Hepsi Bir Arada Yazıcı Epson 7880 - Stylus Pro Color Inkjet Printer için çevrimiçi göz atın veya pdf Manuel indirin. Epson 7880 - Stylus Pro Color Inkjet Printer 12 sayfaları. Warranty statement
Ayrıca Epson 7880 - Stylus Pro Color Inkjet Printer için: Hızlı Başlangıç Kurulum Kılavuzu (1 sayfalar), Ağ Kılavuzu (46 sayfalar), Sınırlı Garanti (12 sayfalar)
![Epson 7880 - Stylus Pro Color Inkjet Printer Manuel](/uploads/products/server2/563838/563838.png)
Follow these steps to align the print head using the control
panel:
1. Make sure the printer is turned on. Then load Epson
Enhanced Matte Paper.
Tip:
To properly align the print head, you can also use Epson
Doubleweight Matte Paper or Ultra Premium Photo Paper Luster.
2. Press the
button.
Menu
3. Press d until
HEAD ALIGNMENT
press
Menu. PAPER THICKNESS
4. Press
. The
Menu
STANDARD
This is the correct thickness setting for most Epson papers.
5. Press
to save the setting.
6. Press l, then press d to highlight
7. Press the
button to highlight
Menu
again.
(uni-directional) is highlighted. This is
Menu
UNI-D
the type of alignment to start with.
8. Press
to start the alignment process.
Each head alignment takes about 7 minutes. The printer's
white beam sensor reads the alignment pattern and adjusts
the printer automatically. Make sure you don't open the
front cover or turn off the printer during this process.
9. When the uni-directional alignment is finished, press the d
button until
BI-D 2-COLOR
to start the bi-directional black alignment process.
10. When the bi-directional black alignment is finished, press d
until
is highlighted. Then press
BI-D ALL
alignment process.
11. When done, press the
alignment mode.
If you want to fine-tune the automatic alignment process, you
can perform a manual head alignment. See your electronic
User's Guide for instructions.
Replacing the Paper Cutter Blade
If you notice that your paper isn't cut cleanly, the cutter blade
may need to be replaced. If you use the blade to cut heavy
stock, you will damage the blade and need to replace it. For a
list of media that are not recommended for use with the
cutter, see the User's Guide or Printer Guide.
You can check the status of your cutter by printing a status
sheet. See page 6 for instructions. You can obtain a new cutter
blade from Epson (part number C12C815291).
9 - Epson Stylus Pro 7880/9880
is highlighted, then
is highlighted.
setting is selected by default.
.
ALIGNMENT
, then press
AUTO
is highlighted. Then press
to start the
Pause button to exit head
Removing the Old Blade
Make sure the printer is turned on, then follow these steps to
remove the blade:
1. Press the
button.
Menu
2. Press d until
MAINTENANCE
.
Menu
3.
CUTTER REPLACEMENT
again.
4. Press
. The print head moves to the replacement
position.
OPEN FRONT COVER TO SEE CUTTER
REPLACEMENT LABEL
5. Open the front cover.
6. When
SEE LABEL TO REPLACE CUTTER
the LCD display, hold down the side pin (as shown to the
left) and turn the latch to the right (as shown on the right).
7. Release the side pin. The cutter pops out.
:
Warning
The blade is sharp. Be careful when removing it.
10/07
Epson Stylus Pro 7880/9880
is highlighted, then press
is highlighted. Press
is displayed.
is displayed on
Menu