Cisco Codec C Series 시작하기 매뉴얼 - 페이지 25

{카테고리_이름} Cisco Codec C Series에 대한 시작하기 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco Codec C Series 41 페이지. Telepresence conference system
Cisco Codec C Series에 대해서도 마찬가지입니다: 사용자 설명서 (44 페이지), 시작하기 매뉴얼 (35 페이지), 시작하기 매뉴얼 (32 페이지), 시작하기 매뉴얼 (42 페이지), 시작하기 매뉴얼 (46 페이지)

페이지 인쇄

Cisco TelePresence Video Systems

Contents

Configuring IP

(When not set by a provisioning system)

Your video conference system supports IP version 4 (IPv4),

IP version 6 (IPv6) and Dual, which is the default setting. In all

three cases, the IP parameters can be assigned automatically

by the network, or you can set everything manually. When set

to Dual, the network interface can operate on both IP versions,

and have both an IPv4 and an IPv6 address.

If you wish to set the parameters manually, contact your network

administrator to obtain the required parameters.

If you choose to set the IP settings manually while using the

Dual mode, you have to set both the IPv4 and the IPv6 settings.

Start from point 2 in the instructions.

If your system is provisioned automatically, these IP settings

may be overridden by the provisioning system.

If an IPv4 or IPv6 address is already assigned to the system, you

can find it on the System Information page. Go to

tab and choose

System Status

and Network.

NOTE:

You must restart the system after changing the IP stack

settings for the changes to take effect.

NOTE:

It is not recommended to manually change the IP addres

using the web interface.

If you are changing a value setting,

you have to always click

save

to confirm the change.

Back to task overview

D14639.12 Video Systems Getting Started Guide TC7.0, DECEMBER 2013.

Introduction

User interfaces

To set or change the IPv4 settings

Go to the

Configuration

Choose IP version

Click the

Network

from the

IPStack

If you wish to set IP Assignment manually

In the

IPv4

SubnetMask

Scroll up to the

address in the

Choose automatic or manual IP assignment

Scroll down the page to the

from the

Assignment

IP assignment; or Static, if you have set the IP address

Configuration

manually.

* IP Assignment:

DHCPv6: All IPv6 addresses, including options like the DNS and NTP

server addresses, are obtained automatically from a DHCPv6 server.

Autoconf: The system and gateway IP addresses will be assigned

automatically. The options, e.g. NTP and DNS server addresses, must be

set/assigned according to the DHCP Options setting. **

Static: The system and gateway IP addresses must be configured

manually. The options, e.g. NTP and DNS server addresses, must be set/

assigned according to the DHCP Options setting. **

Confirguration

Configuration

tab and choose

System

Configuration.

settings in the left sidebar. Choose

drop down list.

section, enter the Address,

Gateway

in the corresponding input fields.

DNS

section and enter the DNS server

Server 1 Address

input field.

IPv4

section and choose

DHCP

drop down list, if you want automatic

Appendices

To set or change the IPv6 settings

Go to the

Configuration

tab and choose

Choose IP version

IPv4

Click the

Network

settings in the left sidebar. Choose

from the

IPStack

drop down list.

Choose automatic or manual IP assignment

and

Scroll down the page to the

DHCPv6,

Autoconf

Static

down list according to your network requirements.*

If IP Assignment is Static: Set the IP addresses

Enter the system IP address in the

Optional: Enter the gateway address in the

field.

If IP Assignment is Static or Autoconf: DHCPOptions

Choose

Off

from the

according to your network requirements.**

If DHCPOptions is Off: Configure DNS and NTP

Scroll up to the

DNS

section, and enter the DNS server

address in the

Server 1 Address

Open the

NetworkServices

and scroll down to the

NTP

address in the

Address

input field. Set

** DHCP Options:

On: The IP parameters, like the DNS and NTP server addresses, will be

obtained automatically from a DHCPv6 server.

Off: The IP parameters, like the DNS and NTP server addresses, must be

set manually.

Getting Started Guide

Contacts

System

Configuration.

IPv6

section and choose

from the

Assignment

drop

Address

input field.

Gateway

input

DHCPOptions

drop down list

input field.

settings from the left sidebar,

section. Enter the NTP server

Mode

to Auto.