Cisco Profile Series 구성 매뉴얼 - 페이지 10

{카테고리_이름} Cisco Profile Series에 대한 구성 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco Profile Series 13 페이지. Jbod on the 12g sas modular raid controller
Cisco Profile Series에 대해서도 마찬가지입니다: 시작하기 매뉴얼 (41 페이지), 사용자 설명서 (44 페이지), 사용자 설명서 (7 페이지), 시작하기 매뉴얼 (35 페이지), 빠른 참조 매뉴얼 (2 페이지), 설치 매뉴얼 (44 페이지), 설치 시트 (2 페이지), 설치 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (4 페이지), 빠른 시작 매뉴얼 (4 페이지), 설치 매뉴얼 (16 페이지), 시작하기 매뉴얼 (32 페이지), 매뉴얼 (16 페이지), 시작하기 매뉴얼 (42 페이지), 시작하기 매뉴얼 (46 페이지)

페이지 인쇄

Configuration Examples

Router(config)# hostname R2

R2(config)# username R1 password cisco

R2(config)# interface serial 0/0/0

R2(config-if)# encapsulation ppp

R2(config-if)# ppp authentication PAP

R2(config-if)# ppp pap sent-username R2 password cisco

R2(config-if)# end

Example: Frame Relay Configuration

This example shows how to configure frame relay encapsulation on a serial interface.

Router1>enable

Router1#configure terminal

Router1(config)# interface Serial 0/0/0

Router1(config-if)# ip address 50.50.50.1 255.255.255.0

Router1(config-if)# encapsulation frame-relay

Router1(config-if)# no keepalive

Router1(config-if)# frame-relay interface-dlci 50

Router1(config-if)# end

Router2>enable

Router2#configure terminal

Router2(config)# interface Serial 0/2/0

Router2(config-if)# ip address 50.50.50.2 255.255.255.0

Router2(config-if)# encapsulation frame-relay

Router2(config-if)# no keepalive

Router2(config-if)# clock rate 2000000

Router2(config-if)# frame-relay interface-dlci 50

Router2(config-if)# end

Example: MLPPP Configuration

This example shows how to configure Multilink PPP on a serial interface.

Router1> enable

Router1# configure terminal

Router1(config)# interface Multilink 1

Router1(config-if)# ip address

Router1(config-if)# no ip route-cache

Router1(config-if)# ppp multilink

Router1(config-if)# ppp multilink group 1

Router1(config-if)# end

Router1(config)# interface Serial 0/2/0

Router1(config-if)# no ip address

Router1(config-if)# encapsulation ppp

Router1(config-if)# no ip route-cache

Router1(config-if)# ppp multilink

Router1(config-if)# ppp multilink group 1

Router1(config-if)# end

Router1(config)# interface Serial 0/2/1

Router1(config-if)# no ip address

Router1(config-if)# encapsulation ppp

Router1(config-if)# no ip route-cache

Router1(config-if)# ppp multilink

Router1(config-if)# ppp multilink group 1

Router1(config-if)# end

Cisco 800M Series Integrated Services Routers Software Configuration Guide

120.120.120.1 255.255.255.0

Chapter 4

Configuring the Serial Interface