Cisco TelePresence MX300 문제 해결 매뉴얼 - 페이지 27

{카테고리_이름} Cisco TelePresence MX300에 대한 문제 해결 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco TelePresence MX300 37 페이지. Telepresence c series telepresence mx series telepresence sx series telepresence ex series
Cisco TelePresence MX300에 대해서도 마찬가지입니다: 매뉴얼 (2 페이지), 시작하기 매뉴얼 (42 페이지), 빠른 참조 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (12 페이지), 빠른 참조 매뉴얼 (2 페이지), 시작하기 매뉴얼 (46 페이지)

페이지 인쇄

Release and option keys

Release keys

A release key is needed to upgrade between major releases, for example when upgrading from TC5.1.5

to TC6.0.0. A new release key is not needed when upgrading between minor releases, for example

from TC5.1.4 to TC5.1.5.

You can check if you have a valid release key for the current software from the web interface. You will

be notified on screen or the Touch device if you have no valid release key (Figure 32).You can check

which release keys have been installed to the system the web interface. You can find this information at

Maintenance -> Software

Upgrade. Next to the release key field you can see all release keys currently

installed on the system (Figure 31).

You can read more about the release keys in the

com/en/US/services/ps10436/ps11105/activation_key_process_guide_services.pdf

To contact Cisco regarding keys, you can e-mail [email protected].

please install the new release key prior to upgrading.

Figure 31 - Check All Release Keys Entered on System

Figure 32 - Web Interface - Check for valid release key

D15029.01 Troubleshooting Guide TC6.0, April 2013.

Activation Key Process

Guide:

http://www.cisco.

Option keys

product options are ordered through normal sales channels and processes. These options must be

activated by installing option keys. Note that this process only applies for options purchased after initial

product purchase. Options purchased with the initial product purchase are shipped pre-activated.

You can read more about the option keys in the

en/US/services/ps10436/ps11105/activation_key_process_guide_services.pdf

The available option keys are:

•

Presentation This allows systems to send a presentation and is now supplied by default on

all new systems. On the EX series you will not see this option listed -it is available by default

in these systems.

•

Dual display Dual display option is needed for C20, C40 and EX90 to use a second screen.

NOTE

On C40 both HMDi and DVi outputs work in mirrored mode without a key. The EX90

will only display far-end presentation or local presentation/pC–input on the second screen.

•

Multisite To allow your video system to call multiple video systems on C40, C60, C90, EX90

and SX20 without the use of infrastructure such as an MCU/Bridge. Without this option we

support a single video call and one audio call.

•

HD Allows 720p at 30fps encode/decode

•

Premium resolution Allows encode/decode resolution of 1920x1080 and 60fps support and

allowing some higher presentation resolutions.

Adding option keys

You can add option keys on the web interface of your system. Navigate to

Here you can find a field to add in new options keys

Add the key you have and press Add. if the key was added successfully, you can see the message

below. if the key is not accepted, check that you are entering it to the correct system as keys are tied

to serial numbers. in addition, check the keys that are already installed. if the key is already there, it

will not be accepted.

Troubleshooting Guide TC6.0

Activation Key Process

Guide:

http://www.cisco.com/

Maintenance -> Software

Upgrade.