Sony BRC-X401 명령 목록 - 페이지 20
{카테고리_이름} Sony BRC-X401에 대한 명령 목록을 온라인으로 검색하거나 PDF를 다운로드하세요. Sony BRC-X401 41 페이지. Srt introduction
Sony BRC-X401에 대해서도 마찬가지입니다: 매뉴얼 (15 페이지), 기술 매뉴얼 (15 페이지)
페이지 인쇄
Command List (7/8)
Number in ( ) is MENU display values.
Command Set
PAN TILT
PAN TILT DRIVE
RAMP CURVE
PAN-TILT SLOW
PAN TILT LIMIT
Command
Up
8x 01 06 01 vv ww 03 01
FF
Down
8x 01 06 01 vv ww 03 02
FF
Left
8x 01 06 01 vv ww 01 03
FF
Right
8x 01 06 01 vv ww 02 03
FF
UpLeft
8x 01 06 01 vv ww 01 01
FF
UpRight
8x 01 06 01 vv ww 02 01
FF
DownLeft
8x 01 06 01 vv ww 01 02
FF
DownRight
8x 01 06 01 vv ww 02 02
FF
Stop
8x 01 06 01 vv ww 03 03
FF
ABS
8x 01 06 02 vv 00 0p 0p
(Absolute
0p 0p 0t 0t 0t 0t FF
Position)
REL (Relative
8x 01 06 03 vv 00 0p 0p
Position)
0p 0p 0t 0t 0t 0t FF
Home
8x 01 06 04 FF
Reset
8x 01 06 05 FF
-
8x 01 06 31 0p FF
On/Off
8x 01 06 44 0p FF
Limit Set
8x 01 06 07 00 0q 0p 0p
0p 0p 0t 0t 0t 0t FF
Limit Clear
8x 01 06 07 01 0q 07 0F
0F 0F 07 0F 0F 0F FF
Command Packet
vv: Pan speed 01 (Slow) - 18 (Fast)
ww: Tilt speed 01 (Slow) - 17 (Fast)
vv: Pan speed 01 (Slow) - 18 (Fast)
ww: Tilt speed 01 (Slow) - 17 (Fast)
vv: Pan speed 01 (Slow) - 18 (Fast)
ww: Tilt speed 01 (Slow) - 17 (Fast)
vv: Pan speed 01 (Slow) - 18 (Fast)
ww: Tilt speed 01 (Slow) - 17 (Fast)
vv: Pan speed 01 (Slow) - 18 (Fast)
ww: Tilt speed 01 (Slow) - 17 (Fast)
vv: Pan speed 01 (Slow) - 18 (Fast)
ww: Tilt speed 01 (Slow) - 17 (Fast)
vv: Pan speed 01 (Slow) - 18 (Fast)
ww: Tilt speed 01 (Slow) - 17 (Fast)
vv: Pan speed 01 (Slow) - 18 (Fast)
ww: Tilt speed 01 (Slow) - 17 (Fast)
vv: Pan speed 01 (Slow) - 18 (Fast)
ww: Tilt speed 01 (Slow) - 17 (Fast)
vv: Pan-Tilt speed 01 (Slow) - 18 (Fast)
For pppp and tttt, refer to the section of the
Pan/Tilt Position (for reference) of VISCA
Command Setting Values
vv: Pan-Tilt speed 01 (Slow) - 18 (Fast)
For pppp and tttt, refer to the section of the
Pan/Tilt Position (for reference) of VISCA
Command Setting Values
p: 1=Sharpness
p: 2=On, 3=Off
q: Position (1=UpRight, 0=DownLeft)
For pppp and tttt, refer to the section of the
Pan/Tilt Position (for reference) of VISCA
Command Setting Values
q: Position (1=UpRight, 0=DownLeft)
20
Comments