Cisco 3110 매뉴얼 - 페이지 21

{카테고리_이름} Cisco 3110에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco 3110 42 페이지.
Cisco 3110에 대해서도 마찬가지입니다: 시작하기 (42 페이지)

페이지 인쇄
Cisco 3110 매뉴얼
Overview
3
5
7
9
For More Information
6-Port 1-Gb SX/10-Gb SR/10-Gb LR/25-Gb SR/25-Gb LR Network
Module with Hardware Bypass
The Secure Firewall 3100 chassis has one network module slot named NM-2. Network modules are optional,
removable I/O modules that provide either additional ports or different interface types. The network module
plugs into the chassis on the front panel. See
slot on the chassis.
The FPR-X-NM-6X1SXF, FPR-X-NM-6X10SRF, FPR-X-NM-6X10LRF, FPR-X-NM-6X25SRF, and
FPR-X-NM-6X25LRF hardware bypass network modules have six ports that are numbered from top to
bottom, left to right. Pair ports 1 and 2, 3 and 4, and 5 and 6 to form hardware bypass paired sets. In hardware
bypass mode, data is not processed by the Secure Firewall 3100 but is routed to the paired port. This network
module has built-in SPF transceivers. Hot swapping and field replacement of transceivers are not supported.
Hardware bypass (also known as fail-to-wire) is a physical layer (Layer 1) bypass that allows paired interfaces
to go into bypass mode so that the hardware forwards packets between these port pairs without software
intervention. Hardware bypass provides network connectivity when there are software or hardware failures.
Hardware bypass is useful on ports where the secure firewall is only monitoring or logging traffic. The

6-Port 1-Gb SX/10-Gb SR/10-Gb LR/25-Gb SR/25-Gb LR Network Module with Hardware Bypass

Ethernet 2/3 and Ethernet 2/4
Ports 3 and 4 are paired together to form a
hardware bypass pair. LED B2 applies to this
paired port.
Ethernet 2/7 and Ethernet 2/8
Ports 7 and 8 are paired together to form a
hardware bypass pair. LED B4 applies to this
paired port.
Power LED
Left Port LED
• Unlit—No connection or port is not in use.
• Green—Link up.
• Green, flashing—Network activity.
• See
6-Port 1-Gb SX/10-Gb SR/10-Gb LR/25-Gb SR/25-Gb LR Network Module with Hardware
Bypass , on page 21
for a description of the 1/10/25-Gb network module.
• See
4-Port 40-Gb Network Module, on page 17
• See
8-Port 1/10/25-Gb Network Module, on page 15
module.
• See
Install, Remove, and Replace the Network Module
network modules.
4
Ethernet 2/5 and Ethernet 2/6
Ports 5 and 6 are paired together to form a
hardware bypass pair. LED B3 applies to this
paired port.
6
Captive screw
Handle
8
10
Right Port LED
• Unlit—No connection or port is not in use.
• Green—Link up.
• Green, flashing—Network activity.
for a description of the 40-Gb network module.
for a description of the 1/10/25-Gb network
for the procedure for removing and replacing
Front Panel, on page 8
for the location of the network module
Overview
21