Sony NEX-F3K 서비스 매뉴얼 - 페이지 13
{카테고리_이름} Sony NEX-F3K에 대한 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Sony NEX-F3K 19 페이지. Interchangeable lens digital camera
Sony NEX-F3K에 대해서도 마찬가지입니다: 사양 (35 페이지), 제한 보증 (1 페이지), 사용 시 참고 사항 (2 페이지), 서비스 매뉴얼 (42 페이지)
페이지 인쇄
2-1-5. IMAGER BLOCK SECTION
ns: not supplied
Cabinet Front Section
(See page 2-9)
208
(Note 4)
207
(Note 4)
206
Ref. No.
Part No.
Description
201
A-1886-976-A
CAB F B-ASSY (SERVICE) (BK) (BLACK) (Note 5)
201
A-1886-977-A
CAB F B-ASSY (SERVICE) (SL) (SILVER) (Note 5)
201
A-1886-978-A
CAB F B-ASSY (SERVICE) (PI) (PINK) (Note 5)
201
A-1886-979-A
CAB F B-ASSY (SERVICE) (WH) (WHITE) (Note 5)
* 202
Selection Parts IM WASHER (A), ADJUST (Note 2, 3)
* 203
Selection Parts IM WASHER (B), ADJUST (Note 2, 3)
* 204
Selection Parts IM WASHER (C), ADJUST (Note 2, 3)
205
A-1868-253-A
MB CHARGE UNIT (757)
206
1-487-619-21
SHUTTER UNIT (H094)
207
4-277-282-11
MB SHEET (754), MASK (Note 4)
NEX-F3D/F3K/F3Y_L2
201
(including CP6001 (CMOS imager)
and IS-101 complete board)
(Note 5)
209
#3
210
204
(Note 2, 3)
203
(Note 2, 3)
#197
#230
205
Imager Unit Section
(See page 2-8)
202
(Note 2, 3)
ns
(Note 1)
Ref. No.
Part No.
Description
208
4-281-196-01
SHEET, MASK SHEET ADHESIVE (Note 4)
209
4-430-449-01
HEAT SINK (720), TOP
210
4-430-450-01
SHEET (TOP (720)), RADIATION
211
4-430-446-01
SHEET (IS (720)), RADIATION
#3
2-660-401-01
SCREW (M1.7), NEW TRU-STAR, P2
#197
4-185-990-01
MB SCREW, CHARGE UNIT FIXED
#230
4-287-434-01
TAPPING (1.7 (ECOLOGY))
#267
4-287-436-21
SCREW (M1.7)
DISASSEMBLY
1. Remove to numerical order (
#267 X 3
1
Back View
#267
#3 X 1
5
#3
Back View
211
Screw
#3: M1.7 X 2.5
(Red)
2-660-401-01
1.7
2.5
Note 1: Refer to "Assembly-1: Screw tightening sequence when
#267
assembling the Heat Sink (IM).".
Note 2: The IM adjust washers (A, B, C) differ in thickness.
Make sure to return the removed IM adjust washers to origi-
nal places.
When replacing IM adjust washers, refer to "2-2. SELEC-
TION PARTS" on page 2-10.
If the original state cannot be restored due to loss of the
IM adjust washer, for example, replace the CAB F B-Assy
(Service).
Note 3: Refer to "Assembly-2: IM Adjust Washer (A, B, C) putting
position" when you assemble.
Note 4: Refer to "Assembly-4: Method of attachment of the MB
Mask Sheet (754)" when you assemble.
Note 5: Precautions for Replacement of the CAB F B-Assy
(Service).
As CAB F B-Assy (Service) may be damaged by static
electricity from its structure, handle it carefully like for the
MOS IC.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.
2-7
to
) in the left figure.
1
5
#230 X 1
3
#197: M1.6 X 4.5 (Tapping)
#230:
M1.7 X 4.0 (Tapping)
#267:
(Silver)
(Black)
4-185-990-01
4-287-434-01
1.6
1.7
4.5
4.0
Note 1: "Assembly-1: Screw tightening sequence when assembling
the Heat Sink (IM)." を参照してください。
Note 2: IM調整ワッシャ (A, B, C)は，それぞれ厚さが異なります。
取り外したIM調整ワッシャは，必ず元の位置に戻してくださ
い。
また，IM調整ワッシャを交換する際は，2-10ページの "2-2.
SELECTION PARTS"を参照してください。
IM adjust washerを紛失するなどして元の状態に戻せなく
なった場合は， CAB F B-Assy (Service) を交換してください。
Note 3: 組立時は"Assembly-2: IM Adjust Washer (A, B, C) putting
position"を参照してください。
Note 4: 組立時は"Assembly-4: Method of attachment of the MB
Mask Sheet (754)"を参照してください。
Note 5: CAB F B-Assy (Service) サービス交換時の注意
CAB F B-Assy (Service) サービスは構造上，静電気により
破壊される恐れがあるため，MOS ICと同様に注意して取り
扱ってください。
また，受光部にはゴミの付着，および強い光がはいることの
ないように注意してください。
Back View
#230
M1.7 X 5.0
(Red)
4-287-436-21
1.7
5.0