Sony STR-DA80ES - Fm Stereo / Fm-am Receiver 사용 설명서 - 페이지 28

{카테고리_이름} Sony STR-DA80ES - Fm Stereo / Fm-am Receiver에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Sony STR-DA80ES - Fm Stereo / Fm-am Receiver 40 페이지. Limited warranty (es products)
Sony STR-DA80ES - Fm Stereo / Fm-am Receiver에 대해서도 마찬가지입니다: 사용 설명서 (39 페이지), 기술적 배경 (38 페이지), 제한 보증 (1 페이지)

페이지 인쇄
Sony STR-DA80ES - Fm Stereo / Fm-am Receiver 사용 설명서

Advanced Remote Operations

Advanced Remote Operations
Operating One Component
While Using Another
(background operation)
You can temporarily operate other components while
listening to or watching a program.
BACKGROUND
1
Hold down BACKGROUND.
2
Press both the corresponding button of the
component you're going to use (see the table
below) and one of the following buttons at the
same time; VISUAL POWER, TV/VIDEO, CH/
PRESET +/–, ANT TV/VTR, D.SKIP, (, 9, p,
0/), =/+, P, r.
Example: To start recording on a tape deck
while listening to a CD
While holding down BACKGROUND,
press 4 (or 5) and press r + ( at the
same time.
The following buttons correspond to the
components.
The button
1
2
3
4
5
6
7
8
9
>10
ENTER
*
Sony VCRs are operated with a VTR 1, 2 or 3 setting
that corresponds to Beta, 8mm, and VHS,
28
respectively.
SYSTEM OFF
VISUAL
SLEEP
LEARN
POWER
SYSTEM CONTROL / FUNCTION
VIDEO 1
VIDEO 2
VIDEO 3
LD
TV
(AUTO CATEGORIZE SYSTEM)
TAPE
DAT/MD
CD
TUNER
PHONO
TV
5.1
CONTROL
INPUT
1
2
3
ON
TV/VIDEO
4
5
6
Numeric and
D.TUNING
DISC
7
8
9
+
ENTER buttons
BACK
CH/
GROUND
SHIFT
ENTER
PRESET
>
0
–
10
RMS/START
ANT
–
+
SUB CH
POSITION
SWAP
TV/VTR
0
)
=
+
D. SKIP
— RMS —
DIRECTION
CLEAR
P IN P
JUMP
9
(
p
P
r
— SOUND FIELD —
TEST
ON/OFF
GENRE
MODE
TONE
EQ/
TONE
BAND
SLOPE
— LEVEL —
+
+
REAR
CENTER
DIGTAL
DIRECT
PROCESSING
–
–
CONTROL
MASTER
BASS
VOL
BOOST
DPC
MODE
MUTING
PROGRAMMABLE
Corresponds to
CD player
DAT deck
MD deck
Tape deck A
Tape deck B
LD player
VCR (remote control mode VTR 1
VCR (remote control mode VTR 2
VCR (remote control mode VTR 3
DBS tuner
DVD player
Changing the Factory Setting
of a FUNCTION Button
If the factory settings of the FUNCTION buttons (page
14) don't match your system components, you can
change them. For example, if you connect a Sony LD
player to the VIDEO 2 jacks, you can assign the VIDEO
2 button to set the remote to control the LD player.
Note that the settings of the TUNER and PHONO
buttons cannot be changed.
Numeric
and ENTER
buttons
1
Hold down the SYSTEM CONTROL/FUNCTION
button whose function you want to change
(VIDEO 2, for example).
2
Press the corresponding numeric button of the
component you want to assign to the SYSTEM
CONTROL/FUNCTION button (6 - LD player,
for example).
For the numeric buttons, see the table in
"Operating One Component While Using
Another" on this page.
Now you can use the VIDEO 2 button to control
your Sony LD player.
To reset the setting to the factory setting
Repeat the above procedure.
*
)
*
)
*
)
SYSTEM OFF
VISUAL
SLEEP
LEARN
POWER
SYSTEM CONTROL / FUNCTION
SYSTEM
VIDEO 1
VIDEO 2
VIDEO 3
LD
TV
(AUTO CATEGORIZE SYSTEM)
TAPE
DAT/MD
CD
TUNER
PHONO
CONTROL/
TV
5.1
CONTROL
INPUT
1
2
3
ON
FUNCTION
TV/VIDEO
4
5
6
D.TUNING
DISC
7
8
9
+
BACK
CH/
GROUND
SHIFT
ENTER
PRESET
0
>
–
10
RMS/START
ANT
–
+
SUB CH
POSITION
SWAP
TV/VTR
0
)
=
+
D. SKIP
— RMS —
DIRECTION
CLEAR
P IN P
JUMP
9
(
p
P
r
— SOUND FIELD —
TEST
ON/OFF
GENRE
MODE
TONE
EQ/
TONE
BAND
SLOPE
— LEVEL —
+
+
REAR
CENTER
DIGTAL
DIRECT
PROCESSING
–
–
CONTROL
MASTER
BASS
VOL
BOOST
DPC
MODE
MUTING
PROGRAMMABLE